Chopper

That is the last gen Studio Creations kit, but it should still clear approval without issue. The only issues I see are the old style 3 piece belt, the double rivets to attach the back belt webbing, and the large strapping holes in the drop boxes. You might want to pick up a new belt and boxes from Studio Creations, but otherwise, everything else should be ok.

Unfortunately, that tank topper is not going to work, even for basic clearance. That's the Don Jarr tank topper and it's very oversized. Once you remove the tank topper you'll need to further trim the top of the tank so it fits more flushly along the back armor, as is shown in the photo Dennis posted. Can you clarify your assembly of the boot holster? Did you cut a slot and push the holster section through the slit? Is the yellow portion glue? The protruding section should not be outwardly visible and needs to be flush. Are you able to trim it without the holster section coming out? Those rank stripes are thick. It's fine to have 4 thicker ones, since we saw that on screen. I recommend you remove the 2 top ones so that you have 4. We are happy to continue to help with your build, but do you know of any armor parties or fellow garrison mates who are experienced armor builders? There's only so much we can do remotely when it comes to armor trimming and assembly. If possible, I do think it might be helpful if you were able to team up with someone and work on the armor build side by side.

Looks good

I'd go with the longer forehead stripes. The Trooperbay logo decal is fine for approval.

FYI, the images in your latest post aren't displaying.

If the tank topper plate is thick enough that, when mounted, it appears as if it was riveted onto the top of the tank, then the indent should be fine. If the indent makes the tank topper flush with the surface, then it would need to be filled.

FYI, E6000 may not work so well for mounting the lens. If it doesn't work for you, most people use hot glue on the inside, along the sides of the lens.

The screen used chin strap used with the cup was just a piece of elastic. However, if it is not outwardly visible then you can do whatever works for you.

Good call. You should be able to cut the welder's shield with a pair of lexan scissors.

That should work just fine.

if you cut the body-facing part of the foam blocks into a L_⅃ shape, then you can use the interior to put stuff into your pouches, while still retaining the shape.

FYI the GA aerator, depicted on the right in the earlier photo, is not accurate and should not be used.

Hi Chris, the CRL is considered both a visual and written guide, so the indents on the tank will need to be filled in. A few folks have recently picked up the galactic armory files and asked us about them. We are still reviewing them for 501st compliance, but we do have a few initial notes which you can read here: https://forum.501stpathfinders.com/topic/24366-doms-scout-trooper-rotj-wip/#comment-230139 https://forum.501stpathfinders.com/topic/24378-galactic-armory-stl-files/#comment-230152

Also, Fibre-Metal by Honeywell FM4001 Quick-Lok Helmet Adapter Kit https://a.co/d/1EQc3Dr

You have to cut a square hole in the sides of the visior shroud to fit them into the sides of the helmet and a round hole in the dome portion of the helmet. It's pretty easy to see once you have the parts in hand. https://forum.501stpathfinders.com/topic/10270-fs-accurate-tb-helmet-hardware-kit-headband-kit-ongoing/

Hey Dom, just a FYI, but the Galactic Armory 3D model does have a few areas that you should address for clearance -- You might want to do some sanding to try and round out that hard edge at the upper corners of the visor shroud. The screen helmets had a much softer edge in that area. The indent above the snout and just below the eyeslot should be flat/flush and it should be covered by a decal once finished. I'm guessing the indent on the bottom half of snout is for the aerator?

A visible seam in the flak vest is okay, but it's also okay if you don't have one. When sewing leather, make sure you're using a leather needle for your machine.

If you'd like to try and commission someone to build the helmet for you, then you might want to post a message in the BST forum. There may be someone who will do it for a nominal fee. https://forum.501stpathfinders.com/forum/155-trade-forum/ Also, Jeff at Studio Creations used to offer fully built helmets. You could also reach out and see if he will build your helmet for a certain price.

If you're talking about the 2" strapping, that should be pure white in all instances of the ROTJ scout.

You will be fine by going with Chef. The Keep Trooping/Imperial Boots gloves are fine as well. Correct, the neck seal is still optional and yes, Darman is the vendor most folks have used for cloth neck seals.

Agreed, that sole color looks good. Thanks for the heads up, Chris.

Congrats!

There is no official pantone color for the scout armor, though I wouldn't go with "off-white". Even the ABS used by the vendors will vary. Generally, I recommend looking for what's typically termed "appliance white" at the hardware store.

You got your kit from Mon Cal, correct? We don't have many clear close up photos of that particular greeb on screen, but we do know that it's the same as part of the endor trooper badge. The examples I've seen of that particular det greeb, including from RS Props, Studio Creations, and others, all have the cylinder on the right. I'm not sure about the original issue with the CRL model, but other pathfinders have the Strider/CfO armor, which is what's depicted, and the greebs that come with it have the cylinder on the right side of the greeb. Detachment staff will address this inconsistency as a part of our annual CRL review. I do not foresee this being an issue for Level 1/Basic clearance. It would be an issue for Level 2/Lancer clearance. Mon Cal's detonator is already listed as not passing Level 2/Lancer, so we can give a heads up there as well, after we discuss any CRL updates: https://forum.501stpathfinders.com/topic/21881-rotj-scout-armor-kit-accuracy-and-level-2-lancer-applications/ If you want to pick up a right side cylinder greeblie, you can get one from Studio Creations: https://studiocreations.com/howto/bikerscout/forsale_bike_replacementparts.html

Ron, if you want to post some photos, please do so and we can take a look.