gmrhodes13

Hello and welcome aboard, research is the key, also look at other build threads.

Correct

Can we also get a measurement on the bund rear closure.

Hi Jonas thank you for the additional photos, we have reviewed and here are our findings: Firstly the black sections (mud flap, leg straps) are hard to see in the photos, I suggest taking photos with better lighting from the front/back Ear holes in helmet are a little rough, could use sandpaper to smooth them out Upper arm armor not in the same position There is a lot of staining on the cummerbund and pouches, looks more like a spilt cup of coffee, we advise washing and perhaps a very light weathering, a mist of black spray paint would be enough. Drop boxes are a little low Straps over your shoulder bridges should be the same colour as your drop box straps Black paint around snout on helmet is a little uneven Looks like the cod section has some curves added to it, should be straight sides Although a blaster is optional for basic approval it is a requirement for Lancer The chest/back straps should be a white cotton webbing Belt closure should be velcro and not plastic clips Could we have close up photos of your boot soles and cut outs. The soles look very dark and should be tan in color, also it looks as if you have missed some cut outs

Thank you for your application, could you also provide a few close up photos, cut outs in boots and armor greebles. We will get back to you once the team has reviewed

Congratulations and welcome to the Lancer ranks trooper

Hello and welcome aboard

Congratulations and welcome to the Lancer ranks trooper

Congratulations once again and welcome officially to the Lancer ranks

Congratulations once again and welcome officially to the Lancer ranks

Just checking in on your application, the team is still waiting new photos to review

Team is reviewing and we will get back to you soon

Team is reviewing we will get back to you soon

Hello Alex thank you for your patience and for making the requested changes. The team has awarded you the rank of Lancer, your profile will be updated shortly. Please send an action pic to Cheyenne (Forest Ranger) and we'll get you added to the wall!

Hello Michael thank you for your patience and for making the requested changes. The team has awarded you the rank of Lancer, your profile will be updated shortly. Please send an action pic to Cheyenne (Forest Ranger) and we'll get you added to the wall!

Team is reviewing

Thank you for the updated photos, we shall review and get back to you.

Once again apologies for the late feedback. There are a few photos we will need, as well as some minor fitment issues. Canvas straps bunched in belt slots, you could open the slots a little more Cod elastic looks too tight, pulling on cod front edge Belt angles down towards the back, could be lifted Pouches could come in a little and upwards slightly Butt flap looks very small but hard to tell from photos, could we have a better from the rear photo showing the width clearly please Bicep armor could come up a little Bund closure looks to be left over right and should be right over left, can you confirm or modify Also need close up photos of the blaster scope

First one I purchased some from a local leather shop, the second one I was lucky enough to find a suede jacket in a second hand store, worked out well. Good luck with the hunting

Apologies we do understand but we are still waiting on some feedback from some of the team, we will get back to you as soon as we can.

Congratulations and welcome to the ranks

Thank you for your patience Michael, there are a couple of things the review team would like: Please even up your vest sleeves, one looks longer than the other in most photos Rotate bicep armor a little Belt is low at back We need close up photos of the blaster (scope, barrel) Shoulder bridge canvas straps are too long please reduce the length TD tube should be painted in a light grey color uniformely (no black gaps at least not regular black gaps)

Sorry for the delay but it is still under review we will get back to you soon.

I managed to find some which go with a welders helmet, I did sand them aa little on the inside of the disc to give a more accurate 3M indented look. Perhaps have a look at one of the safety shops or a Bunnings

Congratulations and welcome to the Lancer ranks trooper