heartstopper85 Posted April 22, 2020 Posted April 22, 2020 It doesn't seem like these go all the way around like the Shoretrooper faulds do, so I think making two separate pieces that hang from the already existing belt is fine. Also, to the extent it helps, my Shoretrooper fauld is 10 inches highYeah need to look at the belt boxes that gives an ideaSent from my SM-G973U using Tapatalk
BikerScout007 Posted April 22, 2020 Author Posted April 22, 2020 1 minute ago, MrPoopie said: I could probably repurpose the Patrol heel file I have into a spat. Does it have that clip on it too? The clip is easy to make. That's what I was thinking. They look very similar
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 I could probably repurpose the Patrol heel file I have into a spat. Does it have that clip on it too? The clip is easy to make.I cant see a clip on figure Sent from my SM-G973U using Tapatalk
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 Can I see a shot of the other side of the spat?Other side Sent from my SM-G973U using Tapatalk 1
MrPoopie Posted April 22, 2020 Posted April 22, 2020 It's difficult to totally nail this down with a measurement of the boots width at the middle of the spat an dthen the length of the spat at the widest and then the height at the tallest point. The front part that you can't see looks similar to the back but it's thinner.
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 It's difficult to totally nail this down with a measurement of the boots width at the middle of the spat an dthen the length of the spat at the widest and then the height at the tallest point. Can you draw the measurements you need. I'm a few drinks in at this point in lolSent from my SM-G973U using Tapatalk
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 Still think it might be ok to use the spats I have I just need to remove clips sand them down do some bondo work to get them smooth Sent from my SM-G973U using Tapatalk
MrPoopie Posted April 22, 2020 Posted April 22, 2020 4 minutes ago, heartstopper85 said: Can you draw the measurements you need. I'm a few drinks in at this point in lol Sent from my SM-G973U using Tapatalk HAHAHA 1
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 HAHAHA 22 cm length 22 width Height 7.5Sent from my SM-G973U using Tapatalk
heartstopper85 Posted April 22, 2020 Posted April 22, 2020 12 width my bad lolSent from my SM-G973U using Tapatalk
MrPoopie Posted April 22, 2020 Posted April 22, 2020 Just now, heartstopper85 said: 12 width my bad lol Sent from my SM-G973U using Tapatalk Thanks. I'll adjust and upload this shortly.
BikerScout007 Posted April 23, 2020 Author Posted April 23, 2020 So I guess this needs to be made to fit a wide variety of leg sizes. It seems that most of the FO costumes have the spats? Do they use velcro to close them? I assume those clips are just greeblies.
heartstopper85 Posted April 23, 2020 Posted April 23, 2020 So I guess this needs to be made to fit a wide variety of leg sizes. It seems that most of the FO costumes have the spats? Do they use velcro to close them? I assume those clips are just greeblies. Yeah I use velcro for my fo spatsKb you can trim to size but bit tallJim Tripons are shorter usually fit a wide variety of sizesCalvin was telling me there are just two halves that connect. I couldn't see the clip on the figure it's clear as day on the pyre in the same pack.Sent from my SM-G973U using Tapatalk 1
MrPoopie Posted April 23, 2020 Posted April 23, 2020 8 minutes ago, heartstopper85 said: Yeah I use velcro for my fo spats Kb you can trim to size but bit tall Jim Tripons are shorter usually fit a wide variety of sizes Calvin was telling me there are just two halves that connect. I couldn't see the clip on the figure it's clear as day on the pyre in the same pack. Sent from my SM-G973U using Tapatalk Most ankles are roughly the same size so there shouldn't be too much variation in the size. If it's ABS you can cut them to size since it'll most likely be 2 pieces. It it's 3D printed you'll just need to scale accordingly. 1
heartstopper85 Posted April 23, 2020 Posted April 23, 2020 Question gaiter do we need the seam Sent from my SM-G973U using Tapatalk
BikerScout007 Posted April 23, 2020 Author Posted April 23, 2020 14 hours ago, heartstopper85 said: Question gaiter do we need the seam Sent from my SM-G973U using Tapatalk We can't see it on the toy so I'd say seam or no seam, either are fine.
MrPoopie Posted April 23, 2020 Posted April 23, 2020 Here are the links to the MT-Spats. The dimensions seem off though. If someone who has boots can print one to see if they're correct it would help. I can adjust the model if it's wrong. If printed in one piece this should just be able to slide over the boot without any issues. MT-Spat_Left MT-Spat_Right My suggestion would be to put some velcro on the inside of the spats (soft side) and velcro sewn at the bottoms of the gaiters (rough side) so everything stays in place nicely. 1
heartstopper85 Posted April 24, 2020 Posted April 24, 2020 I'm going to just mod my spare spats more than likely Not sure who else is building this at moment but is there any opposition to make a smooth no clip fo shaped spat Sent from my SM-G973U using Tapatalk
BikerScout007 Posted April 24, 2020 Author Posted April 24, 2020 26 minutes ago, heartstopper85 said: I'm going to just mod my spare spats more than likely Not sure who else is building this at moment but is there any opposition to make a smooth no clip fo shaped spat Sent from my SM-G973U using Tapatalk I would say we would prefer no clip as we have no reference for one. 1
heartstopper85 Posted April 24, 2020 Posted April 24, 2020 I would say we would prefer no clip as we have no reference for one.Cool easy peasy just some bondo and sanding neededSent from my SM-G973U using Tapatalk 2
heartstopper85 Posted April 26, 2020 Posted April 26, 2020 So pouches I got resized to 6.5x9 I'd like to discuss faulds again I think the prototype soon is the way to go just need to lock down sizing.Than if you dont mind I'd like to pay you (mr poopie) to make mine since I cant sew to save my life. Got a local friend to make me gaiters since I couldn't even do that.Sent from my SM-G973U using Tapatalk
MrPoopie Posted April 26, 2020 Posted April 26, 2020 15 minutes ago, heartstopper85 said: So pouches I got resized to 6.5x9 I'd like to discuss faulds again I think the prototype soon is the way to go just need to lock down sizing. Than if you dont mind I'd like to pay you (mr poopie) to make mine since I cant sew to save my life. Got a local friend to make me gaiters since I couldn't even do that. Sent from my SM-G973U using Tapatalk That should be alright but we'll need to figure out sizing and I have to get supplies which is a little difficult right now. Totally doable though. 2
heartstopper85 Posted April 26, 2020 Posted April 26, 2020 Off the printerSent from my SM-G973U using Tapatalk
MrPoopie Posted April 26, 2020 Posted April 26, 2020 4 minutes ago, heartstopper85 said: Off the printer Sent from my SM-G973U using Tapatalk How do they size up on your shin (roughly)? 1
heartstopper85 Posted April 26, 2020 Posted April 26, 2020 How do they size up on your shin (roughly)? Not sure yet just got pic from my friend. Still figuring out when you pick up but he is same size as me and says everything fits wellSent from my SM-G973U using Tapatalk 1
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now