DukeOfNachos Posted October 12, 2022 Share Posted October 12, 2022 (This may take awhile...) Ordered SC trimmed armor last Thursday (10/6), received the order ship email this morning. (10/12) Armor SHOULD be here Saturday (10/15) by 8pm. Ordered Kolossus Jumpsuit, stripped rear pockets (patched holes) and removed tool pocket (seam ripped the outside and then cut down leg seam so so not to open leg outer seam). Suede should arrive tomorrow (10/13). Quote Link to comment Share on other sites More sharing options...
Jakeputt Posted October 12, 2022 Share Posted October 12, 2022 We have all dealt with accidental tears! Welcome to the forest good sir you're among friends. 1 Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted October 12, 2022 Author Share Posted October 12, 2022 Seriously, those pockets were golden until I had to get to the reinforced corners, that's where it snagged. Now i just need a fabric shopping list to start on the soft parts... once I finish my oldest daughters Jawa so I can drag her along on troops. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted October 21, 2022 Author Share Posted October 21, 2022 CRL on the flight suit says Elastic OR Webbing, with Lancer requiring it to be 2" . I just want to make sure as I have 2" Webbing from making Flare Harnesses that should do the trick right? (Webbing is pic is 2 sewed together for said Flare Harness) Quote Link to comment Share on other sites More sharing options...
Chopper Posted October 21, 2022 Share Posted October 21, 2022 Correct. 2" wide thigh straps, which can be either elastic or webbing. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted October 21, 2022 Author Share Posted October 21, 2022 Awesome, just wanted to make sure that a specific strapping wasn't left out of the CRL for Lancer and then I had to redo something. Quote Link to comment Share on other sites More sharing options...
Aradun Posted October 23, 2022 Share Posted October 23, 2022 On 10/12/2022 at 7:38 PM, DukeOfNachos said:Now i just need a fabric shopping list to start on the soft parts... once I finish my oldest daughters Jawa so I can drag her along on troops. If have links to what I used for my soft parts, most of which was purchased at JoAnn Fabric if you’re looking for stuff. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted October 23, 2022 Author Share Posted October 23, 2022 16 minutes ago, Aradun said: If have links to what I used for my soft parts, most of which was purchased at JoAnn Fabric if you’re looking for stuff. Yessir I’ve started pouring over your build thread, the kolossus jumpsuit looks to be reinforced on both inner and outer parts of the leg. Just the sort of thing to get the anxiety going. Quote Link to comment Share on other sites More sharing options...
OnkelPaschulke Posted October 23, 2022 Share Posted October 23, 2022 Looks like you're off to a good start! I know what you mean with the pockets, the reinforced corners are a real pain in the a**. Just started redoing my jumpsuit yesterday and was sitting in front of my tv and was cursing all the time... 😄 Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 10, 2022 Author Share Posted November 10, 2022 Ok, so I finally put on my big boy pants and cut the holes for the strapping on my armor.. this is the worst part right... Attached (first pass) photos of most parts, I used a diamond cutting wheel and at the end, an endmill bit for the Dremel (if it could REALLY be called that...) https://imgur.com/a/fzDM78b 1 Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 10, 2022 Author Share Posted November 10, 2022 Ok adjusted cuts to fit all the straps, now I have one semi odd question, SC sends a long white 1.5” elastic, and one not quite as stretchy elastic strip, I’m guessing this is the backing strip? Quote Link to comment Share on other sites More sharing options...
Chopper Posted November 11, 2022 Share Posted November 11, 2022 Based on your description, that is likely for the side strapping. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 11, 2022 Author Share Posted November 11, 2022 The side strapping is that 1.5” elastic, piece in general is about calf diameter. On an off note, what’s the sop for over cuts? When I was widening my chest strap cut my blade slipped roughly 1/4” but it’s still in the groove area. https://imgur.com/a/UtjDPuh[/img] Quote Link to comment Share on other sites More sharing options...
Chopper Posted November 11, 2022 Share Posted November 11, 2022 If you want to post a photo of the strap in question, go for it. SC used to send a lot of strapping, and not all of it is always needed as per the CRL. I don't see any issue with the ding marks in your photo. They won't be very noticeable from more than a few feet away. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 11, 2022 Author Share Posted November 11, 2022 The side strapping is that 1.5” elastic, piece in general is about calf diameter. On an off note, what’s the sop for over cuts? When I was widening my chest strap cut my blade slipped roughly 1/4” but it’s still in the groove area. https://imgur.com/a/UtjDPuh[/img] Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 11, 2022 Author Share Posted November 11, 2022 @Chopperugh I feel dumb, said strapping was the elastic for the chest piece 🙄😑 1 Quote Link to comment Share on other sites More sharing options...
Chopper Posted November 11, 2022 Share Posted November 11, 2022 No worries, glad you got it sorted. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 12, 2022 Author Share Posted November 12, 2022 Had some time after work the last few days to do some minor bloodletting while trimming my armor. Got the slots cut, all armor pieces are strapped with the exception of shoulder bells, and top knee strap. Next task this week will be the belt and getting the shoulder bells strapped and adjusted. Helmet hasn't been touched yet because, well, I'm a coward, that'll be last If I can I'm gonna look at also getting my flight suit riding patches/mudflap done this week. Also, the SC v2 armor is nice in that it has the hump setup for the Tank to be riveted... is there a total science to getting the center to attach it? Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 16, 2022 Author Share Posted November 16, 2022 Putting some work in on the belt today, when figuring out strapping for the front I cut off about 17” for the front chevron if you will at the parachute clips really that close to the belt/box? Quote Link to comment Share on other sites More sharing options...
Chopper Posted November 16, 2022 Share Posted November 16, 2022 How does it look when you're wearing it? For Level 2, the drop boxes are supposed to hang approximately 1" under the belt, but for basic clearance there's more leeway there. Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 16, 2022 Author Share Posted November 16, 2022 Belts not fully completed yet, I was waiting on strapping to be figured out to assemble everything as it stands I have about parachute clip distance (1”) between belt/box Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 16, 2022 Author Share Posted November 16, 2022 Rear belt is right over left right? Mocked up, the clip looks like it’s more over the belt/ bit I mean it’s just about where the top of the dropbox hits. Pardon the teenagers room 😐 Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 17, 2022 Author Share Posted November 17, 2022 Started getting the TD done, after an acrobatic mishap while I was attempting to hang the TD to dry (thank god neither Greeb flew off) heres what I have. I'm printing a TD Connector like the 1.5" plastic sink tailpiece @nateopotato brought to life earlier, should know in 6 hours how it turns out . So as it stands, top armor should be all done, have the greebs on the Elbow armor (circles facing up right?). Main belt is assembled ordered some 1.5" cotton strapping, while SC supplied some I didn't realize that it's also for the chest strapping for Lancer as well. Ordered 1" strapping (shoulder bridges). If everything works all hard armor should be completed with the exception of the bucket by this weekend to at least clear basic level (i'll have to adjust the shoulder bridge/chest straps for lancer, but that's minor) 1 Quote Link to comment Share on other sites More sharing options...
DukeOfNachos Posted November 17, 2022 Author Share Posted November 17, 2022 So I’m currently stuck unless I want to go work on softgoods while I’m trying to compartmentalize all the armor. TD just got finished , using the nice sink hack from @nateopotato. Belt Clip placement on the TD, I counted 7 ribs from each end and then drilled between those ribs with a 1/8” bit, then used a 1/8”-3/8” rivet to make sure I had enough meat on the tube interior to grab the washer. So for armor wise it’s either finish the belt (I was going to wait for more webbing to get here to figure the drop boxes ), or tackle the helmet, and I’m kinda worried about the helmet… all four parts of it , also while I’m on the helmet, is there a template floating around for the lens? -> 1-1/2” sink throat piece getting installed -> Completed TD (Front) -> Completed TD (Rear) 1 1 Quote Link to comment Share on other sites More sharing options...
Chopper Posted November 17, 2022 Share Posted November 17, 2022 For a lens template, once your visor slot is cut, trimmed, and sanded, hold a piece of paper behind it and trace the slot with a pencil. Then, add maybe 3/8" or so to the edge of your trace line. Cut that shape out with scissors and that's your template. 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.