Wynterhawk Posted October 10, 2016 Posted October 10, 2016 Hey hey, everyone. The build mission is finally completed. *throws confetti* I was hoping that I could get a few critical eyes to have a look at my photos before I submit for approval. I do see that my vest is sticking up in the back (I'll need to just pull it down) and that I need to pull the balaclava up over my chin. Thank you Armour: SC Flack Vest: DIY Flight Suit: Red Cap DIY Gloves: Wampa Wear Boots: DIY (Pandatrooper's tutorial) Cumberbund and Pouches: DIY Weapon: Pending - DLT-19 from Hyperfirm and Holdout Blaster (way to get a weapon that's nearly at tall as I am ) 3
BikerScout007 Posted October 10, 2016 Posted October 10, 2016 Looks good! I like that your belt, bund and pouch placement are all on point I think for basic you are good to go. However just in case you were interested in Lancer: 1) You need to remove the clips from your gloves 2) The shoulder bells are a bit too long for you. I would lop off about an inch from the bottom and then you can move your other armor up your arm 3) You would need the extra strap and rivets for the knee armor 4) Boot soles need to be cut to match the movie scout. 5) The curve on your codpiece is a chevron and really it should look more like this (ignore the caption text): Looking good though! I look forward to awarding you Pathfinder status once you get cleared by your local GML. And please, go for Lancer in the future 1
Wynterhawk Posted October 10, 2016 Author Posted October 10, 2016 Looks good! I like that your belt, bund and pouch placement are all on point I think for basic you are good to go. However just in case you were interested in Lancer: 1) You need to remove the clips from your gloves 2) The shoulder bells are a bit too long for you. I would lop off about an inch from the bottom and then you can move your other armor up your arm 3) You would need the extra strap and rivets for the knee armor 4) Boot soles need to be cut to match the movie scout. 5) The curve on your codpiece is a chevron and really it should look more like this (ignore the caption text): Looking good though! I look forward to awarding you Pathfinder status once you get cleared by your local GML. And please, go for Lancer in the future Great! Thank you for the feedback. Another excuse to redo the codpiece
Erik R Posted October 10, 2016 Posted October 10, 2016 I like that you made your soft parts yourself, I've always been of the opinion that that's what really makes it yours! 2
Wynterhawk Posted October 11, 2016 Author Posted October 11, 2016 I like that you made your soft parts yourself, I've always been of the opinion that that's what really makes it yours! It's also what took the longest. I was finished with the plastic parts months ago
tk48911 Posted October 11, 2016 Posted October 11, 2016 Looks good! I like that your belt, bund and pouch placement are all on point I think for basic you are good to go. However just in case you were interested in Lancer: 1) You need to remove the clips from your gloves 2) The shoulder bells are a bit too long for you. I would lop off about an inch from the bottom and then you can move your other armor up your arm 3) You would need the extra strap and rivets for the knee armor 4) Boot soles need to be cut to match the movie scout. 5) The curve on your codpiece is a chevron and really it should look more like this (ignore the caption text): Looking good though! I look forward to awarding you Pathfinder status once you get cleared by your local GML. And please, go for Lancer in the future quick question, I also have these same gloves...what's the easiest method to removing the clip from them? thanks! 2
Wynterhawk Posted October 12, 2016 Author Posted October 12, 2016 quick question, I also have these same gloves...what's the easiest method to removing the clip from them? thanks! I found that it can be removed with small pliers 1
tk48911 Posted October 13, 2016 Posted October 13, 2016 I found that it can be removed with small pliers awesome, does it leave a small hole on the glove at all? i will try later tonight...
StoutScout Posted October 13, 2016 Posted October 13, 2016 quick question, I also have these same gloves...what's the easiest method to removing the clip from them? thanks! I just used a pair of scissors and cut the leather loop off that was holding the clip. Sent from my SAMSUNG-SM-G920A using Tapatalk 2
BikerScout007 Posted October 13, 2016 Posted October 13, 2016 quick question, I also have these same gloves...what's the easiest method to removing the clip from them? thanks! An exacto knife does the trick too! 1
Navajo Bro Posted October 14, 2016 Posted October 14, 2016 Victoria did a fantastic job on this and pretty much all by herself! A few of us helped her with some minor assembly details but she gets all the credit and we're happy she finished and it came out looking great 2
Wynterhawk Posted October 15, 2016 Author Posted October 15, 2016 Victoria did a fantastic job on this and pretty much all by herself! A few of us helped her with some minor assembly details but she gets all the credit and we're happy she finished and it came out looking great Thanks so much for your support, Bro.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now