Jump to content

Weasel's Shore Trooper Grunt (NTX3D)


Weasel

Recommended Posts

Edit: Adding a list of finished parts and status (shamelessly yoinked from IRoS ) to keep better track myself:

Last update: 10/31/2023 DONE! :D

Hard parts: 

  • Helmet 
    • Helmet Lens  - Taped the lens into the helmet, might redo it in the future, but for now I'm happy with it.
    • Chin Strap / Cup 
    • Fans & Suspension  - Done, Just need to order a battery that fits better into the helmet
  • Abdomen 
  • Shoulder bells 
  • Biceps 
  • Forearms  
  • Hand plates  
  • Kidney  
  • Belt boxes 
  • Rear belt plate 
  • Greaves 
  • Chest plate 
  • Back plate 
  • E22 Blaster  

Soft parts: 

  • Gloves  
  • Boots  
  • Hip Plates
  • Ammo pouch 
  • Neckseal & Shirt
  • Belt Neck Seal 
  • Baclava 

----------

Original Post:

Hello everyone! After the first few weeks of working on my Shore Trooper Helmet (as part of the entire costume), I figured it was time to make a WIP post.

I am working with the NTX3D files https://www.etsy.com/listing/1478364990/star-wars-rogue-one-inspired and I am pretty happy with the files so far.

My 3D printers (Anycubic Kobra, Artillery X1) on the other hand ... ho boy. I had (and still have) a lot to learn when it comes to working with ABS. I had some issues along the way, which lead to a TON of post processing.

I will not pretend that this went smooth :D Despite some troubles, I am having a ton of fun working on this. It is my first helmet (and costume), so I am expecting many more mistakes along the way.

0-pieces.png

This is the structure. Some pieces were still too big for me to print in one part, so I split the mesh further apart.1-first_pieces_with_resin.jpg

I printed the fins and the front greeblie with my Resin printer. While I am perfectly happy with the durability of the large greeblie, I am either going to print the fins with ABS or give it another go with ABS-like resin. 

2-firstpieces_readytoglue.jpg

3-abs_welding.jpg

I had mixed myself some ABS putty / paste already and glued the pieces together of the face rim, I decided to invest in a cheap little plastic welding tool. I hope the pins will make sure these pieces never come apart. The welding kit was cheap enough and I have a wheelbarrow that needs the same treatment.

4-helmet_back.jpg

The large back helmet piece came out really nice in one part. The raft turned out a bit thick and after tweaking my 3D printing enclosures, I can get away with 1 layer skirts.

5-uhoh_gaps.jpg

As I started to glue pieces together I noticed that not only I had to deal with some warping but that I had also sanded a bit too eagerly... Apoxie Sculpt to the rescue. 

(I also removed the mesh from the greeblie, once I realized I had glued it in at an angle and it was driving me crazy...)

7-fillable_primer.jpg

I made heavy use of Fillable Primer by Rust-Oleum, between sandings.

5-lobotomized_trooper.jpg

At this point I've been sanding and sculpting quite a bit, but the parts of the helmet I had been working on started to come out nicely. I split the top part of the helmet into two smaller files. In hindsight that wasn't my best move ...

7-lower_half_assembled.jpg

Here a better view of the lower half of the helmet assembled, sanded, and heavily sculpted to fix any problems I had with the print.

As mentioned above, spliting the helmet into two pieces wasn't a great idea. Possibly due to warping, the parts didn't line up well. I like to describe the next phase of my project as 'The ABS war crimes'. 

8_abs_war_crime-so_much_abs_putty.jpg

I was refusing to reprint the parts and decided to try to do my best with ABS paste. I could pretend it didn't happen, but I feel posting this is going to be either a cautionary tale or inspiring for someone else. I never said my process was pretty :D

9-so_much_glazing_putty.jpg

At this point I had started making use of Bondo® Glazing & Spot Putty. 

"Versatile formula repairs scratches, pinholes, holes and nick." Nobody says how large those scratches can be ... That being said, it's a great tool to fill slightly separated layers in your prints or deal with layer lines. I was really surprised how dang fast this stuff dries, so I decided to try applying it in a few layers. Once dried, it sands much easier than ABS and allowed me to shape it further without having to wait a day for Apoxie Sculpt to dry.

10-it_fits.jpg

Eventually I had all the pieces together! (minus the fins or the shades). Time for the sandable primer!

12-no_point_in_hiding.jpg

No point in hiding the bumpy front. I eventually did a bit more sanding on the sides that will be visible, but my shame will be hidden behind the mid shield and blast shield!

14-first_sahara_yellow.jpg

Finally, it came time to paint my first pieces with Sahara Yellow by Behr. I am not sure if I got a bad cap, but I had some serious issues with paint sputtering with that can.

14-many_a_tape.jpg

As some will have noticed, the greeblie has been glued onto the mask (I had to do some serious sculpting to make everything fit... did I mention I am stubborn and don't like to reprint things if I can avoid it?) , which meant I had to do some careful taping. 

15-base_color_on.jpg

Would you look at that! It kinda looks like a helmet! After spraying it, I noticed many small details that somehow slipped past me, so I ended up sanding some of it again and adding another coat (not pictured).

I have already made a few mistakes in the weathering process (which I didn't document, because I was too frustrated), but I will try to do a writeup once I have finished that part. 

By my next post I will hopefully have my helmet weathering and shades done. (I haven't forgotten about the logo) Right now my 3D printers are working on the rest of the armor...

 

  • Like 2
Link to comment
Share on other sites

Looking good!

Yeah, ABS can be a bear sometimes, but once you get it dialed in it's really hard to beat.  

Looking forward to more of your progress and let us know how we can help

  • Like 1
Link to comment
Share on other sites

Today, with all the pieces finished and painted, I finally weathered the helmet. 
As it turns out, weathering is quite difficult, even after watching a ton of videos on it. I guess it comes down to pratice and I have never weathered an item like this before (since this is also my first helmet / piece of armor). Initially I had tried another method which caused the paint to change shade (when I rubbed graphite onto it, bad idea), which led me to repaint... long story short, it was messy. I finished it with a coat of matte clear coat to hold the weathering in place.

 

16-weathering.jpg

(I got a kick out of the look with the glasses :D)

While I am not super thrilled with the result, I am trying to be gentle on myself. It's all a learning experience. As a matter of fact, I had just read a relevant post, which made me feel better ^^'

I learned a few lessons in the process and things that I would have done differently. I suspect there will be another printed helmet in my future, but for now, I will continue with the rest of the armor instead, rather than getting hung up on a single piece. I don't want to burn myself out on that. As long as I can reach trooping condition, I'll be a happy camper.

Question: What's usually the final sheen of the armor? Satin or Matte?

I attempted to get the Hobart Face Shield Replacement Lens (https://www.amazon.com/gp/product/B002VECKRO/) into shape with a heat gun and lets just say it didn't go well at all. Now I'll have to wait for another shield. A friend gave me some tips I'll try to follow, but if anyone has some advice on how to create a decent lens, please let me know. I have the final lens shape as a 3D print, but I have a hard time recreating a piece from that lens that I can then use in the helmet.

Link to comment
Share on other sites

9 minutes ago, Weasel said:

Question: What's usually the final sheen of the armor? Satin or Matte?

I attempted to get the Hobart Face Shield Replacement Lens (https://www.amazon.com/gp/product/B002VECKRO/) into shape with a heat gun and lets just say it didn't go well at all. Now I'll have to wait for another shield. A friend gave me some tips I'll try to follow, but if anyone has some advice on how to create a decent lens, please let me know. I have the final lens shape as a 3D print, but I have a hard time recreating a piece from that lens that I can then use in the helmet.

You don't have to clear coat the armor in any way.  Just go with however the Sahara Beige looks out of the can.  

I used a Hobart shield at first, but then I ended up getting one from Mr Paul because I wanted that whole curved lens thing for Level 2.

  • Like 1
Link to comment
Share on other sites

You don't have to clear coat the armor in any way.  Just go with however the Sahara Beige looks out of the can.  
I used a Hobart shield at first, but then I ended up getting one from Mr Paul because I wanted that whole curved lens thing for Level 2.
Honestly, at this point I'd be down to just buy the lens, but I have no seen a listing for the NXT3D models and I'd be too concerned that another lens won't fit. Maybe I will go that route when I go for attempt #2 with the helmet :D

Sent from my SM-S918U using Tapatalk

Link to comment
Share on other sites

Hi, another day another challenge!

I printed the biceps and as it turns out I missed the supports for the straps. I am also not confident about their strength (I never quite trust small pieces like that). Does anyone have any hot tips how to add those back in or knows of a better way to hold them in place thag doesn't rely on these small hooks? I was thinking I could melt a metal rod into the abs, but before I attempt to Frankenstein this, are there better ways? 7af7e02ca64c65e9a1e6dc5cbc655c15.jpg

Sent from my SM-S918U using Tapatalk

Link to comment
Share on other sites

On 7/6/2023 at 2:16 PM, Weasel said:

Hi, another day another challenge!

I printed the biceps and as it turns out I missed the supports for the straps. I am also not confident about their strength (I never quite trust small pieces like that). Does anyone have any hot tips how to add those back in or knows of a better way to hold them in place thag doesn't rely on these small hooks? I was thinking I could melt a metal rod into the abs, but before I attempt to Frankenstein this, are there better ways? 7af7e02ca64c65e9a1e6dc5cbc655c15.jpg

Sent from my SM-S918U using Tapatalk
 

Do like the TK does and use and elastic strap that runs from the shoulder into the bicep to hold it in place. Some use a snap on both ends and others use velcro for adjustability 

  • Like 1
Link to comment
Share on other sites

Snaps and Velcro sound good, that way I can fill up the weird gaps with apoxie sculpt. 

Little update from today: Plenty of printing being done, currently working on my chest piece. I will reprint the helmet blast shield since the other had some bad layer adhesion, so it cracked. I should have applied some 2 part epoxy in the back, which I will do with the new piece.

Now here's a lesson: I had bought the wrong paint. I bought Sahara Yellow NOT Beige,... so as it turns out, I will get another chance of doing the weathering on my helmet! :DAfter sanding and recoating everything with the correct base color.... 

It looked similar enough and Amazon didn't carry a Sahara Beige, so I thought I had the right color. While annoying, I am glad this happened before I sprayed my entire armor with the wrong color.

Even setbacks can be a form of progress.

2023-07-10 19.07.47-25%.jpg

2023-07-10 19.36.17-25%.jpg

  • Like 1
Link to comment
Share on other sites

the wrong paint just gives it that much more layering lol. And yes catching a problem like that is key early in the build. Glad you caught it. Nothing worse than going "done" only to have to start over lol. Keep up the good work, looking forward to seeing the rest.

Link to comment
Share on other sites

  • 3 weeks later...

Time for an update, since I haven't posted in a few weeks. I've been slowly wittling away at the costume, especially the printing parts. As of yesterday I have printed the last piece for the suit, everything else are soft pieces or the straps (which I both intend to buy, once I have the rest of the armor in a good spot).

Since I am paranoid that parts will break at a weak layer line while I am out trooping, I decided to give every piece a good coating of epoxy resin on the inside.
17-resin.jpg

As I mentioned last time, I had to respray the helmet in Sahara Beige, since I had gotten Sahara Yellow first. Tthe cans of Montana seem to have really bad spatter and I am not really sure how to reduce it. I thoroughly shake the cans, and the nozzle is clean, yet I get a lot of this undesirable spatter. Any ideas what I could do to reduce this spatter before I spray the rest of the armor?

18-helmet_spatter.jpg

I used Vallejo liquid mask to have some areas where the pain chipped. While being closeup there are plenty of little things that are discouraging,  tend to I like the overall look. The helmet still requires its stencil and, of course an acrylic weathering.

19_helmet_beige.jpg

While I wanted to wait for everything to be sanded, I decided to start painting the pieces for the belt to deal with the feeling of overwhelm, when I was thinking of the remaining work.

I used liquid latex to remove larger chunks of paint. This is the stage before I went and added more weathering with some sandpaper. They look a little stark on clean pieces, but I assume will blend together with the rest of the weathering.

21.5-_more_pieces_sprayed.jpg

Since I was feeling pretty good about making visible progress on some pieces, I brought the glove plates to the same level, i.e. weathering before acrylic wash. The tip of removing the liner was absolute clutch - they now fit perfectly!

22-gloves_before_acrylic.jpg

This was around the time I got an addition to the family: A Bambu P1S. Part of me wishes I would have invested earlier in this one, but the P1P had no enclosure and the X1C was out of my price range. Bambu Labs to the rescue. If only I had that printing quality on my earlier prints, I would be sanding a lot, lot less :D

20_new_printer.jpg

The "only" things left for it to print were the legs / shins and the armor backplate. The E22 is probably the next project I am going to print on this one. 

A few weeks ago I also dabbled with forming a lens, particularly using vacuum forming, so I made a table that I figured would be big enough (spoiler: it wasn't and the sheets of material weren't big enough as well)

24-vacuum.jpg

I made the form with air dry clay and overall I am pretty happy with how well it held up. The problem came down to that the tinted PC sheet was too small to properly pull over the form. I also had to heat it more to make it bend over the form, which led to bubbles. My first attempt failed miserably, ruining the sheet.

25-form.jpg

The second attempt came out better, but it also required a lot of heating and bending after the fact. There are lots of bubbles from heating the PC too much, but They are actually not too bad when looking through it in the helmet and not visible for an outside observer.

26-result_bubbles.jpg

The helmet is a bit of a mess on the inside, but I am pretty happy with how the lens sits. I think I will make another lens with my form, but with the help of my spouse, so one person can push the sheet onto the form, while the other keeps heating it with a heat gun. That way I should be able to avoid making bubbles inside the PC and get an overall cleaner form. But thats future me's problem.

27-result_inlaid.jpg

This is how the lens looks inside the helmet (this was the old version, before I resprayed it in the correct color).

28-result_in_helmet.jpg

If I went with Sean Field's files for the helmet, I could have ordered a lens from Etsy, which I would recommend, rather than trying to do it yourself, like I did. IF I end up redoing the helmet in the future I will definitely go with different 3D files that have a bit more 'aftermarket support'. At least I learned a good deal from tying to form the lens, and it's serviceable and I can look through it :D

So yeah, lots of work done, tons more to go.

I've tried to avoid sanding, since I want to sand outside, but it has been brutally hot here the past few weeks. With my self-imposed deadline of mid October, I am going to have to really get going. I started listening to the Expanse book series (almost done with Caliban's War), so at least I have good entertainment while I do it!

  • Like 2
Link to comment
Share on other sites

On 8/5/2023 at 2:06 PM, Weasel said:

Time for an update, since I haven't posted in a few weeks. I've been slowly wittling away at the costume, especially the printing parts. As of yesterday I have printed the last piece for the suit, everything else are soft pieces or the straps (which I both intend to buy, once I have the rest of the armor in a good spot).

Since I am paranoid that parts will break at a weak layer line while I am out trooping, I decided to give every piece a good coating of epoxy resin on the inside.
17-resin.jpg

As I mentioned last time, I had to respray the helmet in Sahara Beige, since I had gotten Sahara Yellow first. Tthe cans of Montana seem to have really bad spatter and I am not really sure how to reduce it. I thoroughly shake the cans, and the nozzle is clean, yet I get a lot of this undesirable spatter. Any ideas what I could do to reduce this spatter before I spray the rest of the armor?

18-helmet_spatter.jpg

I used Vallejo liquid mask to have some areas where the pain chipped. While being closeup there are plenty of little things that are discouraging,  tend to I like the overall look. The helmet still requires its stencil and, of course an acrylic weathering.

19_helmet_beige.jpg

While I wanted to wait for everything to be sanded, I decided to start painting the pieces for the belt to deal with the feeling of overwhelm, when I was thinking of the remaining work.

I used liquid latex to remove larger chunks of paint. This is the stage before I went and added more weathering with some sandpaper. They look a little stark on clean pieces, but I assume will blend together with the rest of the weathering.

21.5-_more_pieces_sprayed.jpg

Since I was feeling pretty good about making visible progress on some pieces, I brought the glove plates to the same level, i.e. weathering before acrylic wash. The tip of removing the liner was absolute clutch - they now fit perfectly!

22-gloves_before_acrylic.jpg

This was around the time I got an addition to the family: A Bambu P1S. Part of me wishes I would have invested earlier in this one, but the P1P had no enclosure and the X1C was out of my price range. Bambu Labs to the rescue. If only I had that printing quality on my earlier prints, I would be sanding a lot, lot less :D

20_new_printer.jpg

The "only" things left for it to print were the legs / shins and the armor backplate. The E22 is probably the next project I am going to print on this one. 

A few weeks ago I also dabbled with forming a lens, particularly using vacuum forming, so I made a table that I figured would be big enough (spoiler: it wasn't and the sheets of material weren't big enough as well)

24-vacuum.jpg

I made the form with air dry clay and overall I am pretty happy with how well it held up. The problem came down to that the tinted PC sheet was too small to properly pull over the form. I also had to heat it more to make it bend over the form, which led to bubbles. My first attempt failed miserably, ruining the sheet.

25-form.jpg

The second attempt came out better, but it also required a lot of heating and bending after the fact. There are lots of bubbles from heating the PC too much, but They are actually not too bad when looking through it in the helmet and not visible for an outside observer.

26-result_bubbles.jpg

The helmet is a bit of a mess on the inside, but I am pretty happy with how the lens sits. I think I will make another lens with my form, but with the help of my spouse, so one person can push the sheet onto the form, while the other keeps heating it with a heat gun. That way I should be able to avoid making bubbles inside the PC and get an overall cleaner form. But thats future me's problem.

27-result_inlaid.jpg

This is how the lens looks inside the helmet (this was the old version, before I resprayed it in the correct color).

28-result_in_helmet.jpg

If I went with Sean Field's files for the helmet, I could have ordered a lens from Etsy, which I would recommend, rather than trying to do it yourself, like I did. IF I end up redoing the helmet in the future I will definitely go with different 3D files that have a bit more 'aftermarket support'. At least I learned a good deal from tying to form the lens, and it's serviceable and I can look through it :D

So yeah, lots of work done, tons more to go.

I've tried to avoid sanding, since I want to sand outside, but it has been brutally hot here the past few weeks. With my self-imposed deadline of mid October, I am going to have to really get going. I started listening to the Expanse book series (almost done with Caliban's War), so at least I have good entertainment while I do it!

Looks great so far. I went the other way and started putting fiberglass resin on the outside for added strength and smoothness. For the spatter, in my opinion, its a bad can of paint. there isnt really a way to break it up as I have had this happen a few times and the paint had already started solidifying within the can. I would try and return it for a replacement if possible. But keep up the good work and keep us posted on your progress!

Link to comment
Share on other sites

(Added a Todo / Progress List at the very beginning of the thread that I keep more up to date in between posts)

Time for an update after over a month! I slowed down the last two weeks of August, ignoring the piles of shame (see below) in my workshop in favor of another costume that I created in that time.

31-pile-of-shame.jpg

32-pile-of-shame-2.jpg

After being invited to Renfest, I decided that I would try to make an inexpensive costume. I recreated one of my favorite characters, the Black Knight from Monty Python And The Holy Grail:

32-5-takingabreak.png

It was a lot of fun doing my first costume / cosplaying at an event. It was a lot of fun and I got many great reactions to my costume - it was just WAY too warm for that getup. That's what you get when you got at the end of August here. Doing something different for a bit and then getting the reactions to the costume was incredibly motivating to kick my work on the Shore Trooper into high gear (which involved a ton of sanding at first). 

Since I was doing a lot of armor pieces with plenty of room, I switched from manual sanding to using a detail sander (the ones shaped like an iron) which really moved things along. It still took me a few long nights just sanding away while listening to Audiobooks (currently listening to the Expanse series), but eventually I got there. I then used some filler primer to catch some of my missed spots (and make my life easier). 

33-filler-primer.jpg
34-torso-before-filler-primer.jpg
35-torso-after-fillter.jpg
36-sanding-the-filler-primer.jpg
37-just-more-pieces.jpg

After that it was time for a black coat. I decided to use black sandable primer on top, rather than spraying another Primer + Color combo before the Saharah Beige.

38-black-base-coat.jpg

Then it was time for the Saharah Beige. I followed some advice and ordered new cans of the spray, since the ones from Home Depot were clearly old stock. Suddenly the paint flowed great, without the spatter. Wish I had known that for the helmet, but I'm not going to fret too much about that subtle texturing.

39-painted.jpg

40-painted-2.jpg

I have painted the yellow stripes on the Bicep and the Black and White Stripe on the Shoulder Bell, but have forgotten to take photos.

Then it was time to get the 3D printer going again (It was actually printing while I was sanding) for the E22 Blaster. After talking with a friend, I decided to give making the electronic a shot. A pack of 9V LEDs with attached resistor and a lot of fussing around later, I managed to get it working!

41-e22-lights.jpg
42-e22-lights-hengstler.jpg
43-battery.jpg

I dont have many shots of the E22 in the works. I dry fit everything with tape and once I had the LEDs working glued everything together. For support in the middle I decided to go for a wooden dowel for weight and stability. I sanded a channel on the side of the dowel to feed the cables through. I am missing the lights below the scope, but at this point I didn't really have a good way to add them in anymore.

In retrospect, I should have make the cutouts for the various plastic parts in software (for the 9V compartment for example) and printed them out again, but I don't plan to make another E22 anytime soon. While there are channels for a thin cable to run through, it was a lot of head scratching and cursing under my breath until I got it all to fit and work. The E22 has a lot of rough spots when it comes to sanding, but as long as it looks good in the end without my nose right up to it, I'll be happy.

In my horde of disassembled things, I found round glasses for watches, that will fit nicely into the 3D printed scope. Hoping that will work out, since I really don't have the budget for a replica or original scope.

I have bought materials for the pants and ordered boots & the shirt from Keep Trooping. My personal hope would be to have an approved costume by Mid October, but even then I don't think I'd be able to join some friends in their costume at the Air N Scare, not enough time to register and whatnot, even IF these parts arrived fast enough. I still will try to hold to that date, just to give myself a sort of deadline. 

Link to comment
Share on other sites

Hi Weasel, I’m Conrad , uk garrison ST armourer.
To answer your question as to how I weathered my ST’s well it’s not quick

Been making them for 4 years and I spent about a year researching. My nephew works at Pinewood so I have had incredible help along with Paul Prentice who I know quite well now
Both masters of their crafts.

They were injection moulded in dark brown urethane and so this is the first thing to replicate. All chips and weathering, then goes down to this level to match screen used.
I picked one Grunt and one squad leader from the extensive celebration 2016 photographs and literally had them on screens as I worked. Did my best to copy all the dirt that has built up in the corners, and in all the creases up against the sides of the joining strips and all the chips and scratches. I used liquid mask on the brown base coat, then sprayed Sahara beige and peeled off the masking fluid to reveal chips down to the base coat.
I then did all the wear on the edges and scratches . P80 for heavy scratches p120 for edges. Mini belt sander for real touchdown moments and heavy wear areas as this was used at Pinewood.
Artists acrylic raw umber and black about 60/40 70/30 umber to black mix and add a little water for washes. Brush or rag it on and leave it , then it’s about how much you knock back / take off . Most of it about 70% I rub off then do it again building up your layers. I brushed the creases where it builds up and ragged off again dragging away from the edges to give a soft edge to the dirt. Dissipated. No lines.

For the darker dirt on the flats of the armour here and there dirty down dark brown ageing spray ragged on. For carbon scorch flecks dirty down grey. Both screen used.

Helmet. So it has a ‘tank metal’ kinda look and to recreate this texture I find the point where the can just lets paint out and hold that to spray and build up spitty coats. 2.
Then scratches etc and get a wash on all over and rub most of it off. It naturally finds the low points and stays giving you the overall dirt look. Build up layers of dirt same as above under neck rim , jaw lines , ears , temples etc to match the pics used.
Noticed your symbol is not quite aligned right..the cut out part of it should be in line with the edge of blast plate as indicated.

After all that you should be close to achieving a great screen used look . It’s not easy obviously as they were made by some of the most talented artists in the business so it’s trial and error time but do it enough and you should get the hang of it.
My grunt pics are in the vanguard section for reference. Alternatives for ageing sprays are available outside of the uk. Some pics inside and outside in sun. I did most of dirt work outside in natural light.
Best of luck with your costume.
f445d791cce57e542fc7346241cf1e02.jpg
938152ca41eae848f6bbb4d95a57ea98.jpg
d3b7ae7d82551610f5ead6dd0b31d175.jpg
7e464f4a4ae03bb912b5033a5844cb11.jpg
44818988ae31d9d7c02cfee08eff24e7.jpg
17fa66a39b324ffe29d86e9409f73dde.jpg
7b9b3e2c76e38d3a6ead667eae7f3e29.jpg
b11b01a362c319e2ff022e8bdcb71e41.jpg
b1f7c759e49c4fd413cfe7b6a5d69126.jpg
8b29bba9e47eb2b1eb58880b447f86c4.jpg
cca9b8d622b2d913cd54f83e9f44aa33.jpg
cdb1be461835e0bdc5a3529020072aac.jpg
790869884ec4fb86061a40a7589c89e8.jpg
61909371594d8a79794667fcfd6e9b88.jpg
f740819ac0204dc5caf61ed7f7d4b0da.jpg
2848cce7c46d7bdbdc5a1f66db19ed88.jpg
8ccd34722be91cbb11b97d046691141c.jpg
aced12f119465613bd4f666a826c103a.jpg

f7cb762fd3f6efaa3747b9f9c98f188d.jpg
fa54bc814a40e2ea143d61ed408dafc2.jpg
3c0a71a1d9a430197ee570358d3d0f7e.jpg
d558f4bae9078d82a3761c7c80a228c9.jpg
cba3979622cbbd8d0ee8aac150682784.jpg
f3794ea5d4e67e78f02971486b4eb66a.jpg
83d27f3ce57689d71c3fc7ce21b85b5f.jpg
20c752bf16be8e13d0834d8d6a432a68.jpg


Sent from my iPhone using Tapatalk

  • Like 1
  • Thanks 2
Link to comment
Share on other sites

Haha once again gonna sand down the blast shield to get that spot right, thanks for noticing! 

Those are excellent instructions and I really appreciate you taking the time to answer my question. I hope it'll be helpful for others in the future as well! 

More detail photos of the helmet are also super appreciated! Thank you so much! 

  • Like 1
Link to comment
Share on other sites

Very welcome trooper 2 hrs well spent and I can refer people to your build now via a link ..save me hours Lots of people on here want you on that beach ASAP.. we’re getting hammered


Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

I'm a bit too tired to sort through and upload photos, but I will upload a set soon enough. I have finished all the hard parts! (Except the forearm mounting, for which I will need to hand-sew some velcro into my shirt)

I have some worries about the buckles on the front plate and their L2 eligibility, but at this point I really just want basic approval. The past few weeks have been particularly grueling, but there is finally an end in sight.

I am still waiting for my boots from Keep Trooping (I guess it's not super high on the production list) and I now need to make the pants... Part of me wishes I would have ordered the pants from Keep Trooping as well, but I have the materials and cut out the pattern . Might as well keep myself busy until the boots arrive.

I wonder if I will see any Shore Troopers at the Air N Scare event (I am volunteering as an handler), it'd be nice to actually see the armor in person lol.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...