DanielMayeux Posted May 23, 2022 Share Posted May 23, 2022 Gun- HerosEnd (Etsy) Flight suit, Cummerbund, Cod Piece, pouches and Flak Vest- KriptonTop (Etsy) Boots- Timothy (Etsy) (no longer on site?) Armor- Studio Creations Photos: Link to comment Share on other sites More sharing options...
Chopper Posted May 23, 2022 Share Posted May 23, 2022 Hi Daniel, thank you for your application. In order for the Level 2 review team to evaluate your application, you will need to use a file sharing site to host your photos and post them as images in your application (not links, please). Make sure the images are large enough for the team to view all required details. Application instructions are listed here: http://forum.501stpathfinders.com/index.php?/topic/20150-lancer-deployment-request-rev-2021/ For more information on hosting images, see this thread: http://forum.501stpathfinders.com/index.php?/topic/22990-sharing-photos-with-dropbox/#comment-215704 Once the application photos are posted in the thread, then we can proceed with the application. Thank you! Link to comment Share on other sites More sharing options...
DanielMayeux Posted May 23, 2022 Author Share Posted May 23, 2022 Sorry about that. I figured the Google drive link would work. I've uploaded to a stop box folder and included the link for that folder. Link to comment Share on other sites More sharing options...
Chopper Posted May 23, 2022 Share Posted May 23, 2022 Daniel, sorry, but for the review you have to post the photos in the actual application thread. This makes it easier and more efficient for the review team to go over your application. Please see examples from other applications, such as this one: 2 Link to comment Share on other sites More sharing options...
DanielMayeux Posted May 23, 2022 Author Share Posted May 23, 2022 Okay, photos are uploaded in the correct way now 👍. Link to comment Share on other sites More sharing options...
Chopper Posted June 3, 2022 Share Posted June 3, 2022 Daniel, thank you for your patience. The team has completed their initial review of your application and we have the following notes: Overall: The application is missing measurements for the following: Shoulder bridge strapping Drop box strapping Belt webbing Rivets: Can we please get some measurements of the flange heads on the rivets for your holster, belt, and knees? The team thinks that they look larger than the specified 1/8" hole-size rivets. Thank you. Helmet: Replace the helmet bolts with the 3M bolts. You can get them here: https://www.amazon.com/Fibre-Metal-Honeywell-FM4001-Quick-Lok-Adapter/dp/B002BUMS8Y/ref=psdc_7491811011_t1_B015MG1SMK Flight Suit: Butt flap is long. Trim approximately an inch off of the bottom edge of the butt flap. See example photo: Shoulder Armor: Let the bells out maybe 1/2" and rotate them forward. Currently they're sitting too far back. Gloves: Trim off glove clips. Back Armor: Tank topper needs to get moved forward approximately an inch and needs to be flushly glued down-- in one of the back armor photos the right side isn't glued to the top of the tank. You'll need to drill out the rivet, which you can carefully do with a cobalt drill bit. If the hole is visible then you'll need to patch the bottom side with some ABS scrap and make some ABS paste to fill the hole on the top side. Codpiece: Loosen or extend the codpiece strapping to reduce codpiece wrinkles. Belt: There's a lot of excess velcro visible on the belt, which is evident in the left side photo. The visible velcro will need to be trimmed, as the end of the belt and veclro attachment should not show when fully fastened. Typically, both are concealed behind the detonator box. Boots: Sole color is two tone and will need to be painted as one color. Holster: Round off the edges of the sides of the holster with a file or emory board. The slot cuts are overly thick -- they're just supposed to be razor saw cuts or cut with a very thin dremel wheel. The inside can either be backed with scrap plastic and filled in with ABS paste and refinished, or else the holster will can be replaced. Blaster: The blaster is over-weathered and will need to be painted black. Please provide additional detail photos of the end side of the singlepoint scope. Is that molding flash? It'll need to get cleared up so the details are present. The end side should look like this, with the interior ridges: http://www.501stpathfinders.com/images/scoutopedia/13. Blaster/Hero Blaster back.jpg Overall, your armor and soft goods fitment is quite good. Very nice work. Please let us know if you have any questions, or need clarification on anything we've listed above. Thanks! Link to comment Share on other sites More sharing options...
Recommended Posts