Zugor Posted March 16, 2022 Share Posted March 16, 2022 Not sure if this is the correct location for this type of post but here goes. If your armor has yellowed then I have a cheap and easy solution for you. After much research and watching of videos on the subject and testing the solution. I have found that SalonCare 40 crème safely removes the yellowing from your armor. I bought the 32 ounce bottle but you can get a much smaller bottle as I only used about a half ounce for my helmet. and here is the dome Using rubber gloves and a small paint brush. I slathered a layer of crème over the entire helmet and wrapped it with plastic wrap to prevent the solution from evaporating and laid the parts out in the sun. 1 Quote Link to comment Share on other sites More sharing options...
Zugor Posted March 16, 2022 Author Share Posted March 16, 2022 here are the parts in the sun. I left them out there for about 6 hours. I did occasionally turn them to make sure nothing was in a shadow. 1 Quote Link to comment Share on other sites More sharing options...
Zugor Posted March 16, 2022 Author Share Posted March 16, 2022 After 6 hours I brought the parts in and washed them with soapy water. And as you can see there isn’t any yellow left on the parts. none of the decals or paint was affected in any way. Hope this is helpful to other troopers out there. 1 Quote Link to comment Share on other sites More sharing options...
Tarok Posted March 16, 2022 Share Posted March 16, 2022 Wow, that’s impressive. Did you source the crème locally or online?Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Zugor Posted March 16, 2022 Author Share Posted March 16, 2022 I ordered it through Amazon but I imagine you could find it at any salon type shop. I didn’t think to check with any of the local places and just ordered it. Quote Link to comment Share on other sites More sharing options...
Zugor Posted March 16, 2022 Author Share Posted March 16, 2022 The crème has a 40 percent hydrogen peroxide content so please be careful and wear rubber gloves when handling it. I made the mistake of not wearing gloves while I was turning the parts and got some on my finger tips. My fingers where turning white and had that stinging feeling within minutes. I ran in and washed my hands quickly. Quote Link to comment Share on other sites More sharing options...
Chopper Posted March 16, 2022 Share Posted March 16, 2022 Thanks for this. I've seen mention of this method in the past, but I've also seen comments that it made the plastic more brittle over time? How's it feel in that respect? Quote Link to comment Share on other sites More sharing options...
Aradun Posted March 16, 2022 Share Posted March 16, 2022 Thanks Peter !Sent from my iPhone using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Zugor Posted March 16, 2022 Author Share Posted March 16, 2022 Feels the same to me. The plastic seems to be just as pliable as it was before. No sign of oxidation either, the plastic is nice and shiny. Quote Link to comment Share on other sites More sharing options...
spike Posted March 17, 2022 Share Posted March 17, 2022 UV will kill thermo plastics, keep out of the sun as much as possible. thinner the plastic the worse it is Auto paints will act as a shield from UV I have plastic vac formed items from the 80,s, painted and still good to go another thing that protects auto paint is a silicon polish so you may use that to help cancel some of UV damage cheers 3 Quote Link to comment Share on other sites More sharing options...
spike Posted March 17, 2022 Share Posted March 17, 2022 followup to my last post, you may use a mild abrasive car/auto polish to remove the yellowing and apply silicone at the same time, I use KITTEN brand its a cream not a hand compound. cheers 2 Quote Link to comment Share on other sites More sharing options...
Flykiller Posted April 24, 2022 Share Posted April 24, 2022 Hi ! I have the yellowing issue with my 3 years old biker armor. I'm really afraid of damaging it... Has anyone ever tried painting the armor ? ABS plastic does not support paint ? Thank you, Jérôme Quote Link to comment Share on other sites More sharing options...
Chopper Posted April 24, 2022 Share Posted April 24, 2022 Spray paint adheres to ABS just fine. You'll need to make sure that the plastic surface is clean, then prep the surface by wet sanding with some 600-800 grit sandpaper. Once that's done, you can spray the armor using semi-gloss white, or gloss white paint. I'm not sure what spray paint brands are common in France, so you'd need to check with your local garrison to see what's recommended on that aspect. 2 1 Quote Link to comment Share on other sites More sharing options...
Flykiller Posted April 24, 2022 Share Posted April 24, 2022 Thank you so much for this quick and complete answer. Hope is back 🙂 Have a nice day ! Quote Link to comment Share on other sites More sharing options...
Zugor Posted April 24, 2022 Author Share Posted April 24, 2022 There is also a product called adhesion promoter that you spray on after the light sanding mentioned above. That will keep the paint from flaking off. That being said, I tested the hydrogen peroxide method out on new and old armor, old being FX TK armor and there was no damage at all. 1 Quote Link to comment Share on other sites More sharing options...
rawktrooper Posted July 27, 2022 Share Posted July 27, 2022 the Salon Care stuff works great. You can also get a larger aquarium or clear plastic bin, add some creme to a foil pan and set it in there with the armor.. it will fume the armor and turn it white in the sun. It doesnt last forever, but it only takes a couple hours in the sun to get the yellow off.. some of the pieces of my armor yellowed while in the storage bin with no sunlight whatsoever.. so i think some plastic is more prone to yellowing and other isnt.. this method also works on action figures FYI. Quote Link to comment Share on other sites More sharing options...
mikidymac Posted June 5, 2023 Share Posted June 5, 2023 Hello @Zugor. How is this holding up after a year? I have some badly yellowed armor I need to try and save. Quote Link to comment Share on other sites More sharing options...
Zugor Posted June 6, 2023 Author Share Posted June 6, 2023 On 6/5/2023 at 11:32 AM, mikidymac said: Hello @Zugor. How is this holding up after a year? I have some badly yellowed armor I need to try and save. It's working great for me! I haven't had my armor reyellow yet and I have it out in the sun quite a bit all winter long. I have done it on several helmets, a bunch of armor pieces like my chest plate and back plate. Nothing appears to be weakened either, it's all still flexible like it has always been. My armor is old FX armor that has some updated(newer) parts from other manufacturers so the process works on old and new plastic. Quote Link to comment Share on other sites More sharing options...
mikidymac Posted June 6, 2023 Share Posted June 6, 2023 Awesome, thanks for the update. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.