Jump to content

Recommended Posts

Posted

Hey everyone,

Basically the boots I have currently are in pretty rough shape so I decided to buy some replacements. I was wondering if you guys think it would be possible for me to remove my old holster and put it onto my new boots, or should I just get a replacement?

 

Thanks!

Posted

I don't see why not.  You can drill out the rivets (hopefully) and just move it over to your new boots.

Might be less trouble to get a new holster, but if you want to save money you can repurpose your old one.

  • Like 1
Posted

If you get can a 1/8" cobalt drill bit from the hardware store and you used aluminum rivets, then you should be able to drill out the holster without issue. If you used steel rivets...well, that's not impossible, but it's a little more difficult to drill them out.

  • Like 2
Posted

Bei very careful not to let it get hot while drilling out the rivets, the ABS melts very easily.

  • Like 2
Posted

Given that you’re scrapping the boots and getting a new pair, you could just cut the fabric around the rivet which will free the holster from the boot. The rivets should be loose and have some play in them at that point, so if you don’t have access to a cobalt bit or if they are steel rivets (they’re steel if a magnet sticks to them), then you can use a pair of wire snips to cut the back side of the rivets and that should allow you to push them through to the front. You may need a pair of needle nose pliers to squeeze the cut end so they slip through the hole in the holster. I’ve done it this way without issue because I was lazy and didn’t have access to a cobalt bit. Takes patience though.

  • Like 1
Posted
16 hours ago, FoximalFox said:

Kinda wish this thread was started before I went and removed my holster. Now I have to get a new one.

If you're up to printing one there are files available. Depending on your kit maker most of them are  helpful and can set you up with anew holster pretty easily.

Posted

Thank you all for the helpful replies! I knew it was possible, just didn't know what everyone's take on it was.

  • Like 2
Posted

Let us know how it goes and post some pics if you get a chance, I would like to see the outcome:)

Posted
On 2/19/2021 at 1:40 AM, Lucasfan7 said:

Let us know how it goes and post some pics if you get a chance, I would like to see the outcome:)

Will do!

Posted

So I tackled the process today, got a 1/8" cobalt drill bit and went at it. Some came out easier than others, I eventually cut around the holster to try an make it a bit easier. There aren't really pictures I took that can be of any good help, I just drilled the top of the rivet until they popped out. Like I said some came out easier, I had one that was a bit tricky. I made sure not to get it too hot and with some patience it came out after awhile.

Just an FYI this kit was not mine. In the state I got it, it was clear it was older than it appeared and its condition was to say well worn. I have been trying to restore it but with all the money and work, not to mention replacements, I could have honestly just bought a new one but you live and learn. With that being said, its probably best I get a new holster. Not that I botched drilling out the rivets, but that this one is showing its age. For anyone else trying to do this you will most likely have a better result than me, worked out great with everyone's advice.

  • Like 2
Posted
10 hours ago, ENG_Cyrex said:

So I tackled the process today, got a 1/8" cobalt drill bit and went at it. Some came out easier than others, I eventually cut around the holster to try an make it a bit easier. There aren't really pictures I took that can be of any good help, I just drilled the top of the rivet until they popped out. Like I said some came out easier, I had one that was a bit tricky. I made sure not to get it too hot and with some patience it came out after awhile.

Just an FYI this kit was not mine. In the state I got it, it was clear it was older than it appeared and its condition was to say well worn. I have been trying to restore it but with all the money and work, not to mention replacements, I could have honestly just bought a new one but you live and learn. With that being said, its probably best I get a new holster. Not that I botched drilling out the rivets, but that this one is showing its age. For anyone else trying to do this you will most likely have a better result than me, worked out great with everyone's advice.

Thanks for the honesty brotha, and it wasn’t all for waste. We have all got to see some experience with this situation now so we have an idea of what goes Into it  if we ever have to do it:)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...