SL-Biker Posted November 27, 2019 Posted November 27, 2019 Bill Moore 38411 Southern California Garrison/Inland Empire Squad Armor: Studio CreationsFlight suit: Modified RedKapBoots: Made by myself All soft parts: Made by myself and TB-21129Gloves: TrooperbayBlaster: Mr. Poopie 3D printed Thanks for your time and consideration. Bill 01 - Front 02 - Front Arms out 03 - Back 04 - Back Arms out 05 - Right Side 06 - Right Side Arms out 07 - Left Side 08 - Left Side Arms out 09 - Action Shot 10 - Bucket Off 11 - Blaster Left Side 12 - Blaster Right Side 13 - Blaster Back 14 - Blaster Front 15 - Jumpsuit Front 16 - Jumpsuit Back 17 - Jumpsuit Strap 18 - Jumpsuit Collar 19 - Gloves 20 - Boots Front 21 - Boots Velcro 22 - Boots Side 23 - Boots Holster 24 - Pouch Bottom and Flap 25 - Pouch Height and Side 26 - Cummerbund Ribs 27 Cummerbund Velcro 28 - Cod Piece Strap 29 - Bell Strap 30 - Forearm Straps 31 - Upper Arm Straps 32 - Knee Straps 33 - Belt and Box Straps 34 - TD 35 - Chest Joint and Side Straps 36 - Tank Strap 37 - Tank 38 - Bucket 39 - Bucket Bolt 40 - Bucket Ear Hole 41 - Vest Velcro 42 - Vest Sleeve Ribs
BikerScout007 Posted November 27, 2019 Posted November 27, 2019 Hey Bill! Glad to see you applying for Lancer. I will forward this onto the Level 2 review team. Best of luck!
Chopper Posted December 5, 2019 Posted December 5, 2019 Hi Bill, Thank you very much for your application. I hope you had a good Thanksgiving holiday! Great work overall. We do have some notes for you. Please give them a look and let us know if you have any questions. We've itemized our notes below: Helmet: You should open up the ear holes a bit more. Please reference this photo of one of the screen used helmets as a guide: Additional OPTIONAL note regarding helmet: The Level 2 spec for "no visible seams on the dome" is listed as optional in the CRL, but we did want to note that the step at the join between the cap and back of your SC helmet in photo 39 looks fairly large. We encourage you to adjust the fit between the cap and back, if you can, to make it more flush. If you can't, you could always use a flexible gap filler on the seam, which would also mean repainting the helmet. Flight Suit: Your butt flap appears to be too long. You should trim approximately 2" off the bottom. Shoulder Armor: Your shoulder bells look like they're very close to the shoulder bridges, given the width of your shoulders. Take them out a bit, maybe 3/4" and see how they look. Bund: Your bund is riding low, are you able to pull it up towards your pecs approximately another inch? If it keeps slipping down from your flak vest, you may also want to try securing it in place with some velcro. Cod: The sewn inverted curve on your codpiece appears closer to a chevron shape, rather than an arc or curve as per the screen used cod. You can use this photo as a reference for the proper curve: Drop Boxes: Your drop boxes appear to be riding forward, towards the front of your belt. Can you even them out? Overall, most of our notes are fitment related and you're very nearly there. Again, please let us know if you have any questions or need any clarification. Thank you again!
SL-Biker Posted December 5, 2019 Author Posted December 5, 2019 Hey Corey, Thank you for the critique and corrections. I have made the changes listed above including the ear holes, with the exception of the bucket seam. I totally overlooked that, my bad. I've started the process but it will of course take a couple more days. I will wait until the bucket is finished, then take and submit the corrected pictures all at the same time. Stay tuned...
Chopper Posted December 5, 2019 Posted December 5, 2019 Thank you Bill. Keep in mind that the seam note about the helmet is optional, and as such is not a mandatory Lancer qualification requirement -- we just wanted to note it for your benefit. Good on you if you're going for it!
SL-Biker Posted December 11, 2019 Author Posted December 11, 2019 43 - Front 44 - Front Arms out 45 - Back 46 - Back Arms out 47 - Right Side 48 - Right side Arms out 49 - Left side 50 - Left side Arms out 51 - Bucket Right side 52 - Bucket Left side Attached are the correction photos. I've addressed each issue mentioned above with the recommended changes. Please take another look and let me know. Thanks again for your time. 1
Recommended Posts