Bärenjäger Posted February 28, 2019 Share Posted February 28, 2019 Hello Pathfinders, I have not done a traditional build thread that documented each step of my biker scout assembly, but I nonetheless wanted to post here for feedback on the final product. In advance, I appreciate any and all replies and the time and thought devoted to them. I am just looking to see if anyone might spot something that will hold the costume back from basic approval. Here are my submission photos: Front Back Right Side Left Side Cummerbund & Pouches Cod & Belt Thermal Detonator & Belt Boots I did not include all the submission photos for the sake of brevity but please feel free to request additional photos if, based on these photos, there is an area of concern. Otherwise, if there is a place that tends to snag new pathfinders up during the approval process, I'd be not only happy but grateful to provide a better view. Thank you! ~Eric 2 Quote Link to comment Share on other sites More sharing options...
Chopper Posted February 28, 2019 Share Posted February 28, 2019 Hey Eric. I see a few small, simple refinements that can really improve your look as a scout, but overall I think you've done a really good job! Basic clearance should be easy work for you. Some suggestions: 1) move your pouches outward a bit -- approximately 1". 2) make sure you tuck the upper back side of your bund in, it's sticking out a little bit 3) the visor bolt on your left side seems to be popping out a bit. Is it loose? 4) rotate your bicep and forearm armour forward a bit slightly As I said, it's really just small stuff. But yeah, good job overall on your build. 1 Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted February 28, 2019 Author Share Posted February 28, 2019 42 minutes ago, Chopper said: Some suggestions: 1) move your pouches outward a bit -- approximately 1". 2) make sure you tuck the upper back side of your bund in, it's sticking out a little bit 3) the visor bolt on your left side seems to be popping out a bit. Is it loose? 4) rotate your bicep and forearm armour forward a bit slightly As I said, it's really just small stuff. But yeah, good job overall on your build. Thanks Corey! I will definitely remember these when I am suiting up in the future. As for the helmet bolt, I checked it after I read your reply. It might be that you are seeing a reflection on bolt in the original photo; however, it could just as well be my imagination that it’s flat. Looking at and holding my helmet moments ago, it seemed flush, but I could just be in-denial. Here is a better photo of the left side of the helmet: Quote Link to comment Share on other sites More sharing options...
Chopper Posted February 28, 2019 Share Posted February 28, 2019 That looks fine and I apologize for any confusion there. I think you're right and the reflection made it look like the bolt was slightly out of the hole in the visor. No worries. 1 Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted February 28, 2019 Author Share Posted February 28, 2019 1 hour ago, Chopper said: That looks fine and I apologize for any confusion there. I think you're right and the reflection made it look like the bolt was slightly out of the hole in the visor. No worries. No need to apologize! You’re doing me a favor with your input as you do with many others here on the forums. It’s appreciated. I was just being thorough by following up. 1 Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted March 10, 2019 Author Share Posted March 10, 2019 1 Quote Link to comment Share on other sites More sharing options...
Jakeputt Posted March 11, 2019 Share Posted March 11, 2019 Looks pretty awesome fellow pathfinder your close to Lancer just take those small extra steps!!! Your almost there!!! 1 Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted March 11, 2019 Author Share Posted March 11, 2019 44 minutes ago, Jakeputt said: Looks pretty awesome fellow pathfinder your close to Lancer just take those small extra steps!!! Your almost there!!! Thanks! I plan to make those changes eventually, but I need to acquire a new blaster first— preferably a DLT-19. My holdout pistol is a Hyperfirm and therefore not acceptable at Lancer as far as I know. Appreciate the compliments though! Quote Link to comment Share on other sites More sharing options...
Jakeputt Posted March 11, 2019 Share Posted March 11, 2019 I have a hyperfirm. As long as it meets the requirements listed on the CRL your fine. Mines even a hyperfirm B grade. It just fit the requirements. Submit i can send you The link to my submission pics so you can see what kinds of pics they're looking for? Did you build your kit with the correct strap specifications? Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted March 11, 2019 Author Share Posted March 11, 2019 48 minutes ago, Jakeputt said: I have a hyperfirm. As long as it meets the requirements listed on the CRL your fine. Mines even a hyperfirm B grade. It just fit the requirements. Submit i can send you The link to my submission pics so you can see what kinds of pics they're looking for? Did you build your kit with the correct strap specifications? Interesting, I bought mine from another member who advised me the scope was of the incorrect type for Lancer. Maybe I’ll take a shot at Lancer with it anyways. As for armor specifications, I just need to switch the width of the shoulder bridge coverings, cut out vents in the holster, and switch out the thermal detonator end caps. I believe that’s the gist of the modificafions unless I am missing something. Quote Link to comment Share on other sites More sharing options...
Retrofire Posted March 11, 2019 Share Posted March 11, 2019 Thanks! I plan to make those changes eventually, but I need to acquire a new blaster first— preferably a DLT-19. My holdout pistol is a Hyperfirm and therefore not acceptable at Lancer as far as I know. Appreciate the compliments though! Good morning and congrats on your approval Pathfinder!Hyperfirm is acceptable for Lancer submissions. There are more accurate representations available but we certainly allow them. Looking forward to seeing your Lancer app in the future! 1 Quote Link to comment Share on other sites More sharing options...
Bärenjäger Posted March 11, 2019 Author Share Posted March 11, 2019 9 minutes ago, Retrofire said: Hyperfirm is acceptable for Lancer submissions. Morning, and thanks for the info./congratulations! I’ll get there eventually. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.