ForesterDesign Posted November 10, 2017 Share Posted November 10, 2017 I don't think it's allowed for Lancer, but my goodness is it pretty. Chose to go with a silver filament for natural "metal" weathering, going to primer it black tonight! Quote Link to comment Share on other sites More sharing options...
ForesterDesign Posted November 10, 2017 Author Share Posted November 10, 2017 Whoops - here it is rightside up: https://imgur.com/CC2i0nw Quote Link to comment Share on other sites More sharing options...
BikerScout007 Posted November 10, 2017 Share Posted November 10, 2017 Why wouldn't it be good for Lancer? Unless it varies greatly from the movie blaster, you should be fine. EDIT: Of course that drilled barrel and scope would need to be filled in.... Quote Link to comment Share on other sites More sharing options...
ForesterDesign Posted November 10, 2017 Author Share Posted November 10, 2017 Why wouldn't it be good for Lancer? Unless it varies greatly from the movie blaster, you should be fine. EDIT: Of course that drilled barrel and scope would need to be filled in.... Haha, exacccctly. I have to make it less functional for a higher status! 1 Quote Link to comment Share on other sites More sharing options...
Haydeus Posted November 12, 2017 Share Posted November 12, 2017 One of the nicer 3D printed blisters I've seen. Well done! Quote Link to comment Share on other sites More sharing options...
Haydeus Posted November 12, 2017 Share Posted November 12, 2017 Blasters not blisters. Stupid auto correct Quote Link to comment Share on other sites More sharing options...
Crix Posted May 23, 2018 Share Posted May 23, 2018 Is this the one from thingiverse? https://www.thingiverse.com/thing:42811 I printed one, but unsure if the size was correct.. feels small, but then I've never held a real one either.. I've only just started research on the biker scout.. so i know nothing .. https://i.imgur.com/KPQ11lE.jpg Quote Link to comment Share on other sites More sharing options...
762s Posted May 23, 2018 Share Posted May 23, 2018 I printed one, but unsure if the size was correct.. feels small, but then I've never held a real one either.. I've only just started research on the biker scout.. so i know nothing .. https://i.imgur.com/KPQ11lE.jpg for comparison ... the dvh blaster is about 7 1/2" long and 4 1/2" tall and 2 3/4" wide the pistol grip/trigger guard opening is about 1 1/2" wide and 2 1/2" tall Quote Link to comment Share on other sites More sharing options...
Crix Posted May 24, 2018 Share Posted May 24, 2018 for comparison ... the dvh blaster is about 7 1/2" long and 4 1/2" tall and 2 3/4" wide the pistol grip/trigger guard opening is about 1 1/2" wide and 2 1/2" tall thank you!! seems close... Quote Link to comment Share on other sites More sharing options...
Dragon_a Posted May 25, 2018 Share Posted May 25, 2018 And the big advantage is that they're much lighter than resin or rubber blasters so it won't pull your boot down nearly as much when its in the holster. Quote Link to comment Share on other sites More sharing options...
SikSiks Posted May 25, 2018 Share Posted May 25, 2018 The 3d printed one from thingiverse is slightly smaller than my current hyperfirm. I am going to be printing another at 114% to see if I can match. This is just a press fit photo mostly right off the printer. Quote Link to comment Share on other sites More sharing options...
Crix Posted May 25, 2018 Share Posted May 25, 2018 110 https://imgur.com/gallery/jmaKyzt I made this one at 110% 1 Quote Link to comment Share on other sites More sharing options...
CatfoodRob Posted September 29, 2018 Share Posted September 29, 2018 I printed mine at 106 percent and it is corrrect size compared to a real singlepoint sight . 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.