Shrek Posted January 28, 2016 Share Posted January 28, 2016 Hello guys i have a quick question about the blaster for the biker scout how do most of you guys secure it to your boot as it is a big concern for a newbie like my self thanks Quote Link to comment Share on other sites More sharing options...
wookieevader Posted January 28, 2016 Share Posted January 28, 2016 Use pop rivets and a backing washer or something in every corner so the rivets don't pull through the boot Sent from my LGLS990 using Tapatalk Quote Link to comment Share on other sites More sharing options...
Southscout Posted January 28, 2016 Share Posted January 28, 2016 As Jim says, for the holster to the boot, rivets and washers, for securing the blaster itself, it's just the normal answer; check what Panda did http://forum.bikerscout.net/index.php?showtopic=9781 1 Quote Link to comment Share on other sites More sharing options...
hokie1 Posted January 30, 2016 Share Posted January 30, 2016 What about for the rubber Hyperfirm pistol? Any suggestions since its rubber? Quote Link to comment Share on other sites More sharing options...
Pandatrooper Posted February 1, 2016 Share Posted February 1, 2016 Replace the trigger guard with steel one. Just cut a strip of 1/8" thick steel, bend it in a vice. Drill some holes and install it. Then add your magnets to the holster like on my build. 1 Quote Link to comment Share on other sites More sharing options...
Dart Posted February 1, 2016 Share Posted February 1, 2016 Replace the trigger guard with steel one. Just cut a strip of 1/8" thick steel, bend it in a vice. Drill some holes and install it. Then add your magnets to the holster like on my build. Another option that I use, is to hot glue some thin bits of white craft foam in the holster so that the blaster wedges itself in. I've had kids tug on it and not be able to get it out, and I don't have to modify the blaster at all. 2 Quote Link to comment Share on other sites More sharing options...
stasz Posted February 6, 2016 Share Posted February 6, 2016 You can also drill out the circle (in red) on the hand grip and glue in a rare earth magnet, and sew a little pouch on the inside of the boot enclosing another magnet or metal piece to bind to, or even put Velcro on your trigger guard (in green), and corresponding Velcro in the holster. Honestly, if I'm trooping with my blaster I hold it 98% of the time. But I do think it looks Badass in the boot holster. 2 Quote Link to comment Share on other sites More sharing options...
Griffin-X Posted February 6, 2016 Share Posted February 6, 2016 You can also drill out the circle (in red) on the hand grip and glue in a rare earth magnet, and sew a little pouch on the inside of the boot enclosing another magnet or metal piece to bind to, or even put Velcro on your trigger guard (in green), and corresponding Velcro in the holster. Honestly, if I'm trooping with my blaster I hold it 98% of the time. But I do think it looks Badass in the boot holster. I have a magnet in the round trigger noted in the pic. It corresponds with a piece of white metal secured to the inner section of my holster. It holds my blaster in place perfectly. 2 Quote Link to comment Share on other sites More sharing options...
Retrofire Posted March 21, 2016 Share Posted March 21, 2016 Another option that I use, is to hot glue some thin bits of white craft foam in the holster so that the blaster wedges itself in. I've had kids tug on it and not be able to get it out, and I don't have to modify the blaster at all. Can you provide a pic of the inside of your holster? I have a Hyperfirm and I'd like to try this method before I cut into my blaster. Thanks! You can also drill out the circle (in red) on the hand grip and glue in a rare earth magnet, and sew a little pouch on the inside of the boot enclosing another magnet or metal piece to bind to, or even put Velcro on your trigger guard (in green), and corresponding Velcro in the holster. Honestly, if I'm trooping with my blaster I hold it 98% of the time. But I do think it looks Badass in the boot holster. Sent from my VS985 4G using Tapatalk Quote Link to comment Share on other sites More sharing options...
SpeedRacer Posted June 14, 2016 Share Posted June 14, 2016 Rather than using a strong magnet, would it be feasible to make a small black leather strap with a popper ? One that goes over the back of the handle when the blaster is in the holster ? Quote Link to comment Share on other sites More sharing options...
Bobik96 Posted June 17, 2016 Share Posted June 17, 2016 Rather than using a strong magnet, would it be feasible to make a small black leather strap with a popper ? One that goes over the back of the handle when the blaster is in the holster ? That doesn't seem approvals to me. You could also trim some sticky back Velcro to the front of the trigger guard and the other side in your holster. Nobody will even see the Velcro. It hides in plain site. Quote Link to comment Share on other sites More sharing options...
Stroker Posted June 17, 2016 Share Posted June 17, 2016 Rather than using a strong magnet, would it be feasible to make a small black leather strap with a popper ? One that goes over the back of the handle when the blaster is in the holster ? It wouldn't pass if you could see it. Which I don't like the idea however I've seen some done this way. The magnet is the way to go. It's a super easy mod. 2 Quote Link to comment Share on other sites More sharing options...
drache Posted June 22, 2016 Share Posted June 22, 2016 For the rubber Hyperfirm pistol I was able to embed a small strip of steel into the rubber of the trigger guard and secure with some epoxy - then epoxy in rare earth magnet into the holster - working great. Quote Link to comment Share on other sites More sharing options...
PropReplicator2 Posted August 24, 2016 Share Posted August 24, 2016 Fastest easiest method, for my dads hyperfirm pistol was he took a small strip of Velcro and applied the fuzzy side in the holster and THEN painted the holster with spraypaint to color the Velcro white too. Then he added the rough side of the Velcro strip right under the gun muzzle so its basically invisible. Its virtually in noticeable, and its held up for going on 11 years with NO problems. Sent from my KYOCERA-E6560 using Tapatalk Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.