marktoots Posted February 7, 2015 Posted February 7, 2015 Recently cleared by the UKG this Biker Scout has been assembled by me. The armour and helmet kit was suppied by Chef, along with the blaster. The gloves are SA and the balaclava is UA. I have followed the Lancer CRL during this build. Can you please review and advise on additional requirements/corrections needed to achieve Lancer. Clearance Photos: Helmet: Blaster: Boots and Holster: T-Bits: Tank Topper: TD: Knee Armour: Cummerbund: Flak Vest: Flight Suit: If you need anything else then shout Thanks for your consideration. 1
Chef Posted February 8, 2015 Posted February 8, 2015 Afternoon Mark. The only things that are instantly standing out is the fact that your drop strap ends are poking out from behind the drop boxes, and the scope on your blaster is every so slightly forward. The turret bezel (the wide bit in the middle) should abut the scope ring. And if I'm being really really picky, the belt just needs levelling up ever so slightly (wonky hips like me... don't worry). Beyond that, I think you've done a grand job. It'll go up before the panel for discussion. We'll let you know the outcome. Cheers Rob. 1
marktoots Posted February 8, 2015 Author Posted February 8, 2015 Thanks Rob Hadn't noticed but now you point it out these are not the clearance photos! As the dropbox straps were sorted. I'll post the correct ones Wonky hips are due to short left leg, boot raise is being used but I'm still a little off
marktoots Posted February 8, 2015 Author Posted February 8, 2015 First post has now been edited and the correct full length photos have been added. Thanks Rob for the spot! Will wait for further feedback before correcting Blaster
4505Marcel Posted February 8, 2015 Posted February 8, 2015 Can I ask what size Velcro you have on the back of the vest
marktoots Posted February 8, 2015 Author Posted February 8, 2015 Hi Marcel The velcro on the vest is 2"
Chex Posted February 9, 2015 Posted February 9, 2015 The boots are a littler dirtier then what I usually like to see, but nothing that would hold anything back. Very good job over all on your build, Mark. 1
Darth Voorhees Posted February 10, 2015 Posted February 10, 2015 I Like it. I think its good. Cant see anything that hasnt already been mentioned. Nice Job Mark! 1
marktoots Posted February 11, 2015 Author Posted February 11, 2015 Just wanted to check in and find out whether there was anytging else that needs addrrssing? Gonna sort the blaster tonight so I post some nee photos tomorrow :-)
marktoots Posted February 11, 2015 Author Posted February 11, 2015 Ok, so I have modified the blaster and moved the scope back as advised by Chef. Is there anything else? 1
Chef Posted February 12, 2015 Posted February 12, 2015 Just swing the turrets so they're on the vertical and horizontal... not on the diagonals. Sorry, the picture is from the wrong side, but you get the idea.
marktoots Posted February 12, 2015 Author Posted February 12, 2015 Ah ok. I had fitted it like this as there is a molded ring on the turret bezel diagonally opposite the two turrets which I am currently using as additional anchor point but I'll get it sorted!
marktoots Posted February 12, 2015 Author Posted February 12, 2015 Have rotated the scope so that the turrets are vertical and horizontal as requested
marktoots Posted February 13, 2015 Author Posted February 13, 2015 Thanks for all the comments so far. Are there any other improvements needed?
4505Marcel Posted February 13, 2015 Posted February 13, 2015 Please see announcements, well done brother 1
Recommended Posts