pleasum Posted December 3, 2013 Share Posted December 3, 2013 Hey guys, I built a strap into the top of my holster / boot, but still get sag. I am thinking about installing a rigid item in there like a plastic ruler. Has anyone tried this? Are there any best ways to do it? Any advice would be great! Did my first troop last weekend and have a parade coming up next. I'm trying to avoid the sag syndrome!! Take care and thanks. - Paul Quote Link to comment Share on other sites More sharing options...
bjsavage7 Posted December 3, 2013 Share Posted December 3, 2013 Maybe you could try sewing some industrial Velcro on your pant-leg where it can help hold up the top of the boot. 1 Quote Link to comment Share on other sites More sharing options...
Pandatrooper Posted December 4, 2013 Share Posted December 4, 2013 Just install some elastic Velcro straps on the inside of the boot. The rivets should go through the outer holster, through the white vinyl, through the elastic. Pad the inside slightly with foam to offset the boot shank properly. I haven't had any issues with "holster floppage". Check my build thread http://forum.bikerscout.net/index.php?showtopic=9781&st=120 1 Quote Link to comment Share on other sites More sharing options...
chimei Posted December 4, 2013 Share Posted December 4, 2013 it might be that your vinyl is just too thin. finding that "just right" vinyl is tough... 1 Quote Link to comment Share on other sites More sharing options...
Chef Posted December 4, 2013 Share Posted December 4, 2013 I've never suffered this personally. Where I have seen it, it has been due to a combination of thinner vinyl, and the top of the boot opening being too wide. But as has been suggested, a good solution would be either a large patch of velcro, or a couple of poppers in the top section of the boot, and corresponding bits on the leg of your suit. 3 Quote Link to comment Share on other sites More sharing options...
Grantd1* Posted December 4, 2013 Share Posted December 4, 2013 I use a foam kneepad velcroed to the inside to ensure ridgidity - works a treat 1 Quote Link to comment Share on other sites More sharing options...
jyjellyfish77 Posted December 4, 2013 Share Posted December 4, 2013 I've used the foam underneath and also Panda's method. Seems to fix it. 1 Quote Link to comment Share on other sites More sharing options...
Griffin-X Posted December 4, 2013 Share Posted December 4, 2013 I also do not have this issue. Mostly, because I rarely holster my blaster. It's always in my hand! But, when I do, my DUFF blaster sits nicely in the holster with no sag. 1 Quote Link to comment Share on other sites More sharing options...
pleasum Posted December 5, 2013 Author Share Posted December 5, 2013 You guys are great! I appreciate all the feedback. I do think the vinyl may be part of the problem. Guess I have to hunt for some new stuff and assemble some boots. In the meantime, I have some tinkering to do with velcro and such. I appreciate all the great suggestions. I did put a strap on the inside, but I may have to tweak that a bit it seems. Thanks guys!! - Paul Quote Link to comment Share on other sites More sharing options...
NegativeEleven Posted December 9, 2013 Share Posted December 9, 2013 I've been struggling with this myself. I put a piece of sintra the size of the holster inside the boot that I riveted thru. I've got elastic around that, snaps around my leg. I've also got snaps at the top of the boot attached to my suit (inside and outside of leg). It still likes to droop about 3/4" lower than the other one. I might try some foam in there next weekend. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.