batninja Posted March 2, 2013 Share Posted March 2, 2013 After taking a break from costuming for a few months, I'm taking another crack at the scout trooper boots. In this case, I'm doing this pair for my buddy Wesclone in Germany. Again, I started with a pair of Rugged Outback 'Cheyenne' work boots from Payless Shoe Source. The pair pictured first is actually my size 12 Ewok-stompers, but all the other pics are of Wes' size 9. After masking and marking the cut lines, I used an X-Acto knife with a thin chisel blade (#17) to cut the area. As opposed to my previous attempt, I made shallow cuts, which closer match the original boot. Then came the fun part! I had dreaded this step in the past, because I used 'natural' heat, leaving the boots on the dash of the car in the summertime, and sweating like a pig for a few minutes at a time to stretch the vinyl over the boot. THIS time, I used a heat gun, and was done in a matter of minutes. A couple of lessons I learned from past attempts: insert socks into the boot before forming the vinyl. Without them, the vinyl will actually 'collapse' the boot toe if you stretch it too tight. Using socks, the form stays rigid. Also (and this is from experience), I used elastic instead of laces. It makes it SO much easier to get suited up, and still tight enough to make the boots feel comfortable. I had Wes test-fit these before he was deployed overseas. Quote Link to comment Share on other sites More sharing options...
batninja Posted March 2, 2013 Author Share Posted March 2, 2013 I carefully removed the push pins, and used an X-Acto blade to cut along the dotted lines left by the pins. Using Shoe Goo, I slathered the boot, smoothed it with my finger, then placed the vinyl. To eliminate 'bunching' along the toe, I used masking tape to help form the edge. It is important to keep checking the vinyl over the next hour or so to make sure it's forming correctly and not shifting with the glue. Keep an eye on it, and make adjustments if necessary. Quote Link to comment Share on other sites More sharing options...
batninja Posted March 2, 2013 Author Share Posted March 2, 2013 After the glue dries (I left it overnight), it was time for the 1/2" edging strips. To accomplish this, I taped two X-Acto knives together, with the blades parallel, and pulled the vinyl through the double blades. Due to the diameter of the X-Acto knife handles, the result is a near perfect 1/2" strip! Here's a shot of the boot with the strip added. Again, monitor the strips for about an hour, as the glue might cause the strips to shift. More to follow... Quote Link to comment Share on other sites More sharing options...
Griffin-X Posted March 2, 2013 Share Posted March 2, 2013 Looking good Eric! Quote Link to comment Share on other sites More sharing options...
Pandatrooper Posted March 2, 2013 Share Posted March 2, 2013 Looking great! The shallow cuts look way better! Quote Link to comment Share on other sites More sharing options...
Boba Leo Posted March 2, 2013 Share Posted March 2, 2013 Good job!!!!! Leo Quote Link to comment Share on other sites More sharing options...
Guest wesclone Posted March 2, 2013 Share Posted March 2, 2013 Nice job, Eric. I'm gonna LOVE my boots!!! Wes Quote Link to comment Share on other sites More sharing options...
bwattsup Posted March 3, 2013 Share Posted March 3, 2013 Well done as always Eric. I always enjoy your WIPs/tutorails. Quick question though. Did you basically use elastic in place of shoestrings for the entire length, or just the bottom portion of the shoe? Just curious. Quote Link to comment Share on other sites More sharing options...
batninja Posted March 3, 2013 Author Share Posted March 3, 2013 I lace the whole thing with elastic. After a few walkabouts, the wearer can trim the top edge of the vinyl to adjust if necessary. Quote Link to comment Share on other sites More sharing options...
bwattsup Posted March 3, 2013 Share Posted March 3, 2013 Cool. I'll give it a try when I make my boots. Thanks for the tip! Quote Link to comment Share on other sites More sharing options...
batninja Posted March 3, 2013 Author Share Posted March 3, 2013 Alright, let's wrap this project up! Prior to painting the soles, I worked on the pattern for the shaft. Wes is a little shorter than me (let's face it, he's just a bit taller than a hobbit! - just kidding, Wes!), so I modified my existing boot shaft pattern, by taking an inch off the top. I made another modification to the pattern that allows for the slight downward curve from the back of the boot around the heel, see here: On to the painting! Quote Link to comment Share on other sites More sharing options...
batninja Posted March 3, 2013 Author Share Posted March 3, 2013 I masked and painted the sole with Krylon Fusion Satin Khaki. After it dried, i finished it off with a misting of Krylon Matte Finish, to take the shine off. And here is the finished project! The shaft and dog bone are not glued on yet. Final construction will be completed by Wes. Thoughts and comments are welcome! Quote Link to comment Share on other sites More sharing options...
Boba Leo Posted March 4, 2013 Share Posted March 4, 2013 Very professional job, congratulations Eric!!!!! Leo Quote Link to comment Share on other sites More sharing options...
Guest wesclone Posted March 4, 2013 Share Posted March 4, 2013 They look great, Eric! Quote Link to comment Share on other sites More sharing options...
Griffin-X Posted March 4, 2013 Share Posted March 4, 2013 Nice job sir, you have serious boot cobbler skillz indeed! Quote Link to comment Share on other sites More sharing options...
jyjellyfish77 Posted April 16, 2013 Share Posted April 16, 2013 Well done! Quote Link to comment Share on other sites More sharing options...
jyjellyfish77 Posted April 17, 2013 Share Posted April 17, 2013 Did you put a rivet on both sides? I have one on the outside and I think I'll put one on the inside also. I haven't seen anything about putting one on the inside. Quote Link to comment Share on other sites More sharing options...
batninja Posted April 25, 2013 Author Share Posted April 25, 2013 jyjellyfish77, I've never used rivets on any of the boots I've made. I know the tutorial suggests this, but I've never had an issue with simply using Shoe Goo. Mr.Bojangles, I hadn't thought about it. But, I do have to start carving my own boots here in a few days, so I'll try to snap a bunch of progress pics! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.