ZanderCage

Ya but sometimes the DLT-19 is to big for some troops.

Thanks. I'll do this.

I just want to get people's opinion on here. Do you think it would be acceptable to troop with my E-11 as my ROTJ Scout at non LFL events?

Sounds good. Thanks for the info. Ya I'm planning on cutting the bi-pod off.

Does anyone know a place where I could buy a completed Dlt-19x scope? Im looking to convert my Dlt-19 to a DLT-19x and this is the only piece I need. I would be ok with having to assemble and paint it myself but finished would be perfered.

I have my cod velcroed to my flightsuit and the end of the strap has velcro on both sides and it is attached to the Cummerbund where the two sides meets. Sorry if that's a bad explanation lol it's late.

I ended up useing JB Weld plastic weld and it worked great. Had some difficulties with shaping the reinforcement pieces but that because I'm not the best with a heat gun. Thanks everyone.

When you say capacitor part what part are you referring to? Also I would probably perfer magnets if possible cause it would be a one and done kinda thing. But I'll keep the velcro in mind.

So for context about 80% of the troops my Garrison does we don't have handlers and all of us are wearing helmets so it's hard to keep and eye on the tiny blaster in the boot holster. I'm just wondering if you guys would have any advice for securing the blaster to the boot holster for those troops I just want it to sit there so a kid can't grab it or it won't fall out while I move. I was thinking of zip tieing it to the holster but I can't think of a way that I could do that so that the zip tie isn't visible.

Thank you very much.

Sounds good thanks. I think I'm leaning more towards the JB Weld plastic weld cause I believe abs cement does get quite warm. Do you have any advice on placement or any tips? Just wanna make sure i get it right the first time and not make mistakes.

Hi everyone. So I'm looking to reinforce my RS Scouts chest piece with some ABS strips on the back of the crease and I'm wondering what kind of plastic weld you would recommend useing? I see people recommending devcon plastic weld but it doesn't seem like that is readily available where I'm from would JB Weld plastic weld work or should I get ABS cement?

My suit was approved by my GML. I just have to wait for my 501st profile to be updated and then I'm good to wear it.

Thanks for the advice I appreciate it. I'll wait to hear from my GML and then I'll make those changes.

Just sent in my submission pictures for basic approval. Let me know what you think. Any advice is appreciated. https://drive.google.com/drive/folders/1u6QVsIaEiJOxr34iPCQzr9-ICGP56pMY

For anyone reading this post in the future YES they are still giving out the Cummerbunds with these colored pouches. Just received my order today and they look like this.

That's this is exactly what I needed.

Hi everyone. So I'm gonna be adding the Upper Strap to my knee armor soon and I was wondering if anyone could tell me the exact measurements of where the rivet is supposed to sit. If you can direct me to a tutorial thread if one exists that would be helpful to. Thanks everyone.

Just recently purchased an rs full commission with the soft goods myself. Do we know if this issue with the pouches is still happening? Just asking so I can start looking at a replacement if needed.

I did get the soft goods with the commission. I really hope I get the right color pouches with it. If they do end up coming with the wrong color pouches are there any vendors that just sell the pouches?

Thank you very much. I will definitely post pictures once it arrives.

Hi everyone this may have been asked before but I've looked and couldn't find an answer. So I recently purchased a RS Prop Masters full commission built ROTJ Scout trooper and I've seen some people mention that the straps that hold the belt boxes on are made of white elastic. Will this pass level 1 approval or will I have to change it for white cotten webbing? I am also wondering if anyone else has gotten the full commission build from RS and if they needed to change anything before they were approved? I am also aware that I will need to make sure the armor fits me well before submitting for approval. I'm more just concerned about the belt.

Thanks. I already ordered one last week.

Do you know of anyone else that may sell finished DLT-19X's? Just incase it takes them awhile before they start taking orders.

No problem man its completely understandable . Will you be making an official post anywhere saying the you can place on order? Or will it just go up on your Esty store?