Bolt

Undersuit: Modified and dyed (With Rit). Army Surplus "British Desert DPM" camo trousers and shirt. Shirt has top button removed and replaced with velcro flap (so it is not visable). Neck seal, velcro for shoulders and elastic stirups added. Pants: Rear pockets removed, side pockets removed, riding patches added. Knee velcro added, Thigh pouches added and stuffed with foam rubber. Suspenders added. Elastic foot stirups added.

Cod piece: Scratch built, foam covered in fabric. I wanted a flexable cod so I could sit on a speeder bike. Attaches with velcro to the cummerbund and pants.

Pouches: All scratch made from foam and coated in fabric. All pouches have velcro closure and are functional. Two front and two rear long pouches. 7 inches high x 4 inches wide x 1.5 inches deep 2 small front pouches with slanted tab. 2.5 inches high x 4 inches wide x 1.5 inches deep 8 small side pouches -Top ones are 3 inches tall x 4 inches wide x 1.5 inches deep - Bottom ones are 4.5 inches tall x 4 inches wide x 1.5 inches deep Two long back pouches 4 inches high x 7 inches wide x 1.5 inches deep

Cummerbund: Custom made All pouches, belt and cod attached Drop pouches and belt stay attached. Can be removed if absolutely necessary. Belt clip detail Drop pouches

Gloves: Wampawear (later version)

Shoulders: Bikerchick. Have underarm straps and kneepads inside to make them sit up on the shoulders (rather than flat).

Biceps: Bikerchick with custom 3d printed parts

Forearms: Bikerchick

Elbows: Bikerchick

Boots: Crow Boots (repainted+velcro added)

Chest and back: Bikerchick kit. Straps are ABS Tank Top detail

Shins: Biker Chick version with custom 3d printed clips. Open clamshell style. Weathering detail.. I mixed actual beach sand in with the paint for texture.

Helmet: Biker Chick version

Hello there! I am CB-33827 "Bolt" from the Redback Garrison, Queensland Australia. https://www.501st.com/members/displaymember.php?userID=16603&costumeID=36 After some prompting from BikerScout007 I would like to apply for Level 2. I have used the CRL as a reference but I mainly sourced screenshots and official lucasfilm renders from Revenge of the Sith. - Armour kit: BikerChick - Boots: Crow Boots - Gloves: WampaWear - Undersuit: Modified and dyed Army Surplus "British Desert DPM" camo trousers and shirt - Cummerbund: Custom made by my amazing wife - Pouches: Scratch made from foam and covered with fabric - Bicep & Shin greebles were 3d printed. - DC-15a & DC-15s: Woodchuck I have yet to take pictures of my individual armour parts, but I will post them here as soon as I take them. I just thought I would get the thread going! This is my full kit: Front - Left Side - Back - Right Side - Discrepancies with the CRL: I did make a few discoveries that varied with the CRL, this caused my approval to be a little difficult to put it lightly... I thought I would post them here for you guys as they may not be acceptable for level 2. -Chest: The CRL states that the chest and back join flush at the sides. From my research I think they do not actually meet, but there is a gap between them and that they are connected by a clip. This is a screen shot from ROTS, it may be hard to see, but the edge of the chest is noticable and you can see the cummerbund past where it ends: This is a scan from the Star Wars Chronicles Prequel Trilogy book. I noticed two tabs either side of the chest. These tabs can also be seen in the "Helmets Collection" magazine which has renders from the film Star Wars Battlefront 2 (Despite having some difference to the movie version) shows these clips a little more clearly. It is difficult to tell what colour exactly the strap and tab were, so I matched the grey colour used for the straps and tab on the Attakus 1:10th scale Kashyyyk trooper. (I can take pictures of the statue if needed). -Bicep Greeble: I also noticed a second greeble on the inside of the left Bicep which isn't mentioned by the CRL. So I designed and 3d printed one for my kit: - Cummerbund: I also had a few issues getting my cummerbund approved as my straps were slighty larger than what was stated on the CRL (at the time) and I added ribbing details which also are not in the CRL. This was my research: In this image from "The Helmets Collection" magazine (also seen in the SW Chronicles book) you can see ribbing between the straps and on the main belt. I used this as a reference when I made my cummerbund. I also made the straps slightly larger so that I had the same number of straps across the front of my body as the movie troopers (I am wider than the CGI clone troopers). And so I added the details to mine: (Colour is off in this picture, I will upload better ones when I get a chance). Those are the issues that are know to me, I thought I would highlight them for you guys so that I can be completely transparent. As I stated earlier, I will be taking picures of all my parts on the weekend and will post them asap. Thank you all for your time and consideration. - Bolt