Jump to content

TB-61708 requesting Lancer status (APPROVED)


Recommended Posts

Hi

It's time for me to apply for Lancer status ! Ok, my little story... I received my SC kit in august 2016 and then, worked hard to build my costume too be most accurate as possible. For it, I followed the incredible topic of Pandatrooper too help me in my build !!!

I got my standard approval last april (the first pics), and since, I trooped 3 times, and I maked minors ajustments : my drop boxes were a little bit too low, so I mounted these a little (you can see on my trooping pic), I maked a light weathering, and on my helmet, I removed trapezoide decals to painted it to have the good size and then, they were more realistic!

So, I hope I have not forgotten anything... and hope my english is correct !... Here's my info and pictures, enjoy!

 

Sebastien Goulet

TB-61708

Forteresse Imperial Garrison, Quebec, Canada

 

Armor & Helmet : SC

Helmet Decals : TrooperBay

TD clips : The Clip

Cotton Webbing : Country Brook Design & Organic Cotton Plus

Boots : Marcel

Undersuit, Flak Vest, Cummerbound, Cod, Pouches : KryptonTop

Balaclava : Under Armour

Gloves : Wampa Wear

Blaster : Polymer Armory

 

bCAe33j.jpg

gxJN1a5.jpg

XZct3EF.jpg

EId0rJW.jpg

 

Comparaison Pic:

U4uhXbu.jpg

 

Picture with my drop boxes mounted:

MWRXQKb.jpg

 

Softparts:

0SMK9mj.jpg

isKdgy4.jpg

xp3JPcU.jpg

n0BSXdm.jpg

Zagq84U.jpg

mkARUHA.jpg

9W3qWDy.jpg

 

Helmet:

aJne3pm.jpg

xvQnJMJ.jpg

jLE8y2O.jpg

 

Armor:

vYazVM6.jpg

eTJzFmT.jpg

lH6Rvsi.jpg

iJuWIAf.jpg

R8qrTsQ.jpg

3f3nuQU.jpg

 

Belt & TD:

cDFudh4.jpg

xqgYhbU.jpg

EDatrfW.jpg

BQIC9yE.jpg

mPF14CY.jpg

 

Arms & Knees parts:

00zNS72.jpg

9R7i1oS.jpg

jHo6XgB.jpg

OQrzOaY.jpg

2uCHzs9.jpg

jVdOPnc.jpg

oWexCYv.jpg

Link to comment
Share on other sites

Thank you for your submission we will get back to you once your application has been reviewed

Link to comment
Share on other sites

Thank you for your patience, the team have reviewed and ask that you make the following changes:

 

- Shoulder bells should rotate and come a bit closer to the shoulder bridges

- But flap looks a little long and covering leg elastic

- Drop boxes too low they are covering leg elastic

- Cod elastic loose

- Pouches could do with an iron

- Blaster has a lot of silver weathering, generally they are not weathered

- Could we have a close up of your helmet screws

Link to comment
Share on other sites

HI, I'm back with my modifications, thanks for the list !

 

- Shoulder bells should rotate and come a bit closer to the shoulder bridges

 

I think it's good like that:

Ju3I3v7.jpg

 

 

- But flap looks a little long and covering leg elastic

- Cod elastic loose

 

I shortened the flap to the right length and the elastic is tighter:

9LHVueV.jpg

 

 

- Drop boxes too low they are covering leg elastic

 

I adjusted the height of my boxes, hope there's ok like that:

E3yg1ht.jpg

 

 

- Pouches could do with an iron

Thanks to my wife :) :

9NgBQBJ.jpg

 

 

 

- Blaster has a lot of silver weathering, generally they are not weathered

 

Ho, okay, it's because I found a rare reference image of a props of the blaster in that forum (next picture), with weathering, so I painted it like that.

No problem, so, I removed a little bit the silver effect, I have done some retouching to decrease the weathering, hope it's ok like this.

Reference picture:

3hL5dTv.jpg

My blaster with retouching:

YQWjR43.jpg

 

 

- Could we have a close up of your helmet screws

 

H4Cqh3F.jpg

 

Thanks

Link to comment
Share on other sites

Thank you for the updates we will require another set of photos from you fully kitted up please.

Link to comment
Share on other sites

Thank you we will get back to you once we have reviewed.

Link to comment
Share on other sites

We have reviewed and we can't quite make out the detail on your helmet bolts, could you please measure them and also provide a photo showing they have an indent. From CRL: â—¾Gray 3M bolts or replicas of in the helmet. (Visible bolt head diameter of 22mm).

 

 

 

 

 

Link to comment
Share on other sites

I'm not very good in english, what's an indent ? Thanks

Normally the 3M bolts have an indent, recess, taper in the centre.

 

photo-211.jpg

 

We will confer and get back to you soon.

Link to comment
Share on other sites

Thank you for your patience Sebastien, the team have agreed everything falls under the guidelines and are happy to approve you as a Lancer, your profile will be upgraded presently. Congratulations and welcome to the ranks.

Link to comment
Share on other sites

Oh Great !!!! Thanks very much :)

I will go take a few pictures in a forest near my home soon and I will send a good action picture to Forest Ranger to be add to the wall ;)

Thanks again!

  • Like 2
Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...